ABLETON 12 SOUND DESIGN ATLAS

Mixing for Sound Systems — Deep Dubstep, Deep Techno & Bass Music

The complete chapter on making deep dubstep, deep techno and 140 bass music work on big rigs in Live 12: sub mono and phase, kick/sub tuning and hand-off, headroom, DC and infrasonics, crest factor and why systems punish over-limiting, honest loudness figures for DJ use and streaming, dubplate practice, live dub mixing, translation checks, club PA realities, mastering chains and DJ-ready stems and edits.

Difficulty
Intermediate
Live edition
Standard and up
Max for Live
In some recipes

A sound system is an instrument with its own rules. Below roughly 100 Hz it is almost always mono, the sub stack may sit metres away from the tops, the amplifiers have limiters of their own, and the room adds its own resonances to every note. Deep dubstep, deep techno and 140 bass music are written for exactly that situation: the sub is the lead instrument, the space between hits is part of the groove, and the whole point is weight you feel in the chest at a level a home system never reaches. This chapter is about the decisions that only matter at that scale. General gain staging, limiter staging and LUFS tables are on Loudness & limiting; stereo tools are on Mid/side & stereo; the ten ways to duck are on Sidechain & ducking; phone/car simulations are on the Listening checklist. Here we go specific to big rigs and these three genres. Assume 140 BPM halftime for dubstep and 140 bass (a bar is 1714 ms, a 1/16 is 107 ms), and 124–128 BPM for deep techno (at 124 BPM a bar is 1935 ms, a 1/16 is 121 ms).

How to read the claims. Statements about artists, studios and systems are marked Documented with a link to the source, or By ear where they come from listening and scene knowledge. Engineering statements (wavelengths, periods, harmonic maths) are physics and need no label. Numbers marked “starting point” are opinions to try, not specifications.

Theory that matters on a big rig

Why the low end has to be mono (and where it does not)

At 50 Hz the wavelength is 6.9 m (343 ÷ 50); at 41 Hz (an E0 in Live’s naming) it is 8.3 m. Nobody localises a source at that size, so PA designers sum the sub feed to mono and spend their boxes on level, not stereo. Any part of your sub that lives in the Side channel (L−R) is simply missing from that feed, and any part that is partly out of phase between L and R arrives at the sub amplifier already reduced. Above the sub crossover the tops are usually stereo, but most of the dancefloor stands far off-axis from one side or the other, so wide mid-bass is heard as a level that changes as you walk. The rule this site uses everywhere (sub mono below ~120–150 Hz) is the safe version. Vinyl is a separate argument, covered in Cut for the system, where one respected cutting engineer calls strict mono bass a myth.

Sub periods, and why fast gain changes click

One cycle of a 41.2 Hz sub lasts 24.3 ms; of a 49 Hz sub 20.4 ms; of a 55 Hz sub 18.2 ms. A duck, gate or fade that moves gain substantially inside one cycle bends the waveform and produces a click or a thump. That is why sub ducks need attack and release times measured in tens of milliseconds, while kick drums, whose transient is the point, can be shaped in single milliseconds.

Crest factor, PLR and what a system does with them

Crest factor is peak level minus RMS level. A sine wave has 3 dB. A dynamic deep dubstep drop, where a kick and snare punch over a sustained sub, might measure 10–14 dB peak-to-RMS; a heavily limited master can fall to 6 dB or less. The loudness-domain version you can read off any LUFS meter is PLR, the peak-to-loudness ratio: true peak minus integrated (or short-term) LUFS. A master at −9 LUFS with a −1 dBTP ceiling has a PLR of 8 dB; one pushed to −5 LUFS at −0.3 dBTP has 4.7 dB.

Why it matters at the system: the DJ and the sound engineer set the level by peaks and by ear. A low-crest master at the same peak level carries more average power, so it reaches the amplifiers’ and speaker processors’ protection limiters sooner and the system engineer pulls the gain down. When that happens the dynamic track, turned up to the same trim, has bigger transients on a rig that can reproduce them, and the crushed one just sounds flatter. The general engineering point (low-crest signals put more continuous power into drivers and amplifiers) is standard PA practice; how hard any particular rig limits is not something you can know from the studio.

The DJ chain does not normalise like a streaming service

Streaming services turn loud masters down to a target. A DJ mixer does not, but it has a trim (gain) knob on every channel, and DJ software such as rekordbox offers an auto-gain analysis. In practice the DJ matches tracks by ear and channel meter, so extra loudness on your master mostly gets trimmed away; what remains is the shape of your dynamics. This is the honest version of “club masters must be loud”: they must not be noticeably quieter than the records around them, and beyond that there is little to gain.

Every dB of limiting you add in the studio is a dB that a system with 20 dB of extra headroom could have played as transient. Big rigs reward peaks; small speakers reward density. That single trade-off is the core of this chapter.

Live 12 tools for system work

Live has no correlation meter and no dedicated loudness meter in the core set. Everything else you need is stock. Parameter names below follow the Live 12 manual (Live Audio Effect Reference).

DeviceRelevant controls (manual names)Job on this page
UtilityBass Mono, Bass Mono Frequency (50–500 Hz), Bass Mono Audition; Width with a Mid/Side mode in its context menu (0–100M, 0–100S); Mono; Phase L/R; DC; Gain (−inf to +35 dB)Mono sub, side-solo checks, polarity checks, DC removal, gain staging
EQ EightLow/high cut at 12 or 48 dB/oct, shelves, bells, notch; Stereo / L/R / M/S modes; Oversampling (context menu)Infrasonic filter, side low cut (elliptical-style), band-solo listening
EQ ThreeLow/Mid/High gain down to −inf, band On/Off, 24 or 48 dB crossover slope, FreqLo/FreqHiDesk-style kills for live dub mixing
SpectrumBlock, Channel (L, R, L+R), Refresh, Avg, Graph, Max, Scale X (linear/log/semitone), Range/AutoReading the sub fundamental as a note, comparing references
TunerClassic / Histogram views, Hertz/Cents switch, Reference 410–480 HzTuning kick tails and sub notes
LimiterInput Gain, Ceiling, Maximize (Ceiling becomes Threshold), Release / Auto, Lookahead 1.5 / 3 / 6 ms, Link, Ceiling Mode Standard / Soft Clip / True Peak, Routing L/R or M/SFinal ceiling; True Peak mode for streaming masters
Glue CompressorRange, Soft Clip (output max −0.5 dB), sidechain with EQGentle bus density, soft-floor sub ducks
Multiband DynamicsThree bands, Above/Below thresholds, Soft Knee, RMS/Peak, Time, AmountLow-band control, dynamic tamer for horn-top harshness
Saturator / RoarSaturator curves (Analog Clip, Soft Sine, Bass Shaper…); Roar Shaper Bias, Multi Band and Mid Side routingClipping above the sub only; sub harmonics for small speakers
EchoFilter (HP/LP with Res), Feedback, Reverb with Reverb Location (pre, post, inside feedback), Noise and Wobble (Amount, Morph), Ducking (Threshold, Release)Tape-style dub delay and throws
Hybrid ReverbConvolution IR menu (includes a Springs category), Algorithm, EQ (Pre Algo), Stereo, Bass Mono (sums below 180 Hz)Spring reverb, mono-safe reverb tails
Operator / Analog / WavetableLFO to pitch, envelopesDub siren, test tones
Shaper / LFO / Envelope Follower (M4L)Rate sync, curve drawing, MapGrid-locked sub ducking at halftime
Build one “System” audio effect rack once (sub-band splits, side solo, tops-only, mono) and save it to the User Library. Every technique in the translation section below uses part of it.

Techniques

Sub mono and phase

Bass Mono per source, with the crossover chosen per genre

Device: Utility · Level: essential · Genres: deep dubstep, deep techno, UK bass

Quick start

Load
Utility
Set
  • Sub: Utility last in the chain, Bass Mono on, 100–120 Hz
  • Kick mono outright (mono sample or Utility Mono)
  • Rumble return Bass Mono 120–150 Hz
  • Stereo mid-bass Bass Mono 150–200 Hz
  • Bass Mono Audition the whole sub on the sub; only the body, not the character, on the mid-bass
You should hear
A sub feed that gets all of the low end in mono while the mid-bass keeps its stereo movement.
Live edition
Intro and up

Put Utility with Bass Mono on each low-end source (sub, kick, rumble return, mid-bass) rather than once on the master. On a source you can hear what the fold does; on the master you also collapse reverb lows and pads you may want to keep wide. The crossover is the decision: high enough to catch everything the sub stack will play, low enough not to mono the movement of a stereo mid-bass.

  1. On the sub, Utility last in the chain, Bass Mono on, Bass Mono Frequency 100–120 Hz. Click Bass Mono Audition: you should hear the whole sub and nothing that sounds like a different instrument.
  2. On a stereo mid-bass (Reese, growl, chord-bass), set the crossover at 150–200 Hz. Audition again: you should hear only the body, not the character. If the character disappears in Audition, the bass depends on stereo lows and will change on a mono sub feed.
  3. On the deep techno rumble return (reverb or distorted kick wash), Bass Mono at 120–150 Hz. Reverbs are the most Side-heavy thing in a mix; Hybrid Reverb’s own Bass Mono (fixed at 180 Hz per the manual) is an alternative inside the device.
  4. Leave the kick in mono from the start (mono sample or Utility Mono). A stereo kick sample is common in packs; its lows are rarely identical in both channels.
SourceBass Mono FrequencyWhy
Sub (sine/triangle)100–120 HzAll of a sub’s energy sits below this anyway; it costs nothing
KickMono outrightThe click can be centred too; width on a kick reads as smear on a big rig
Deep techno rumble return120–150 HzReverb low end is wide and partly anti-phase
Stereo mid-bass (UK bass, roller)150–200 HzKeeps the stereo motion of the harmonics, folds the body
Pads / chords150–250 Hz, or a side low cutTheir lows belong to the bass anyway
Bass Mono above ~250 Hz on a chord-bass also monos the lower harmonics that make it move. If the bass sounds lifeless after Bass Mono, lower the frequency; do not remove the Utility.

Side-solo check: hear exactly what a mono sub feed will lose

Device: Utility (Mid/Side mode), EQ Eight · Level: essential · Genres: all three

Quick start

Load
Utility, EQ Eight, Spectrum
Set
  • Master: Utility Width context menu Mid/Side, 100S
  • EQ Eight band 8 as a 48 dB low-pass at 150 Hz
  • Loop the loudest drop; solo groups to find the source
  • Compare flip the Utility to 100M
  • Before export deactivate the whole chain
You should hear
Only the low end that lives in L−R, the part a mono sub stack never plays; ideally almost nothing.
Live edition
Standard and up

Live has no correlation meter, but Utility’s Width control has a Mid/Side mode in its context menu that runs from 100M (mono sum only) to 100S (Side only). Put that at 100S on the master, then low-pass the result. What you hear is the low end that only exists in L−R: the part a mono sub stack will never play.

  1. Master chain, after everything: Utility, right-click Width, choose Mid/Side, set 100S. Then EQ Eight with band 8 as a 48 dB low-pass at 150 Hz.
  2. Loop the loudest drop. If you hear the sub note clearly, find the track: solo groups with the check still on.
  3. Flip the same Utility to 100M (Mid only) for comparison: that is roughly what the sub feed receives.
  4. Spectrum after the EQ shows the level; anything within ~20 dB of the Mid sub level at the same frequency is worth fixing at the source.
  5. Deactivate the whole chain before export. A forgotten 100S Utility on the master is a silent bounce.
General mono toggles and the null test are on Mid/side & stereo. The point here is narrower: listen to the Side channel below the sub crossover, because that is the only part of the stereo image a sound system throws away completely.

Polarity and phase between kick, sub and layers

Device: Utility (Phase L/R), Operator, Simpler · Level: intermediate · Genres: all three

Quick start

Load
Utility, Operator
Set
  • Loop a bar where kick and sub overlap
  • Sub: Utility Phase L + Phase R both on; keep the louder, fuller setting
  • Operator oscillator phase retriggered on each note if neither polarity wins
  • Sampled kicks nudge the Simpler start a few ms, or shorten the tail
  • Utility Bass Mono 120 Hz after
You should hear
At the kick and sub overlap the hit lands full and solid instead of sucking inward.
Live edition
Suite

Two low sources at the same frequency add or cancel depending on their phase. On headphones a 3 dB loss at the kick/sub overlap is hard to hear; on a sub stack it is the difference between a hit that lands and one that sucks inward. Check every pair that overlaps below 120 Hz.

  1. Loop a bar where the kick and the sub (or two sub layers) overlap. Put Utility on the sub and switch both Phase buttons on. Listen at the overlap and watch the master peak: the louder, fuller setting is the right polarity.
  2. If neither polarity is clearly better, the phase relationship changes during the note (pitch envelope on the kick, slide on the sub). Fix the timing instead: in Operator, set the oscillator to retrigger its phase on each note so every sub note starts at the same point of the cycle.
  3. For sampled kicks, nudge the sample start in Simpler by a few ms against the sub, or shorten the kick tail so the hand-off is clean (see the hand-off technique below).
  4. Layered subs (sine plus a triangle an octave up) need the same check; a free-running second oscillator drifts in and out of phase and the level wobbles.
Two equal sines in phase sum to +6 dB; 180° apart they cancel completely; 90° apart they sum to +3 dB. A kick tail at 50 Hz meeting a 50 Hz sub can land anywhere on that scale, and because the kick’s pitch is falling, the relationship sweeps through several of those states in one hit.

Sub and kick

Tuning the kick and the sub with Tuner and Spectrum

Device: Tuner, Spectrum · Level: essential · Genres: deep dubstep, deep techno, UK bass

Quick start

Load
Simpler, Tuner, Spectrum
Set
  • Tuner (kick soloed) Histogram view, Hertz; read where the trace flattens: the tail note
  • Spectrum Scale X semitone, Block 16384 (or 8192)
  • Simpler Transp and Detune until the tail sits on the key root or fifth
  • Sub repeat on each held note
  • Owner deep dubstep: the sub; deep techno: often the kick at 45–60 Hz
You should hear
Kick tail and sub on related notes, so the low end stops beating and sounds clean on a big rig.
Live edition
Standard and up

On a big rig the kick’s tail is a note. If it settles a semitone away from the sub’s root the low end beats and sounds muddy, and the room (see Room modes) will exaggerate whichever is closer to its own resonance. Tune the tail to the key root or its fifth.

  1. Solo the kick. Tuner in Histogram view shows the pitch drop over time; note where the trace flattens. That is the tail note. Switch to Hertz to read the frequency.
  2. Spectrum, Scale X set to semitone, large Block (8192 or 16384) for low-frequency resolution. The tallest low peak should sit on a note name.
  3. Transpose the Simpler (Transp and Detune) until the tail sits on the root or the fifth of the track’s key. For synthesised kicks, set the pitch envelope’s end value instead.
  4. Repeat for the sub. Sustained sines read cleanly on Tuner; with slides, check each held note.
  5. Decide which one owns the fundamental. In deep dubstep the sub usually does and the kick tail is short; in deep techno the kick often owns 45–60 Hz and the bass sits higher or alternates (By ear: scene convention, not a rule).
Live noteHzPeriodTypical role (By ear)
E041.224.3 msDeep dubstep sub root; below many horn subs’ comfortable range
F043.722.9 msDubstep sub root
F#046.221.6 msDubstep sub root
G049.020.4 msSub root; common kick tail in techno
A055.018.2 msKick tail; sub root for brighter rigs
C165.415.3 msNear the infra/bass-bin split of the rig below
Live note names put C3 at middle C, so the sub octave is 0. The Note to Hz table has every value.

Arrangement before sidechain: let the kick and sub take turns

Device: none (MIDI editing) · Level: essential · Genres: deep dubstep, UK bass

The cleanest duck is one you never need. In halftime dubstep the kick usually lands on beat 1 and the snare on beat 3 of the bar; the sub can start a 1/16 or an 1/8 after the kick, rest under the snare, and come back. Nothing competes, so nothing needs ducking, and the sub keeps its full sustain where it plays. Documented: Attack Magazine’s bassline tips make the same point in general terms: don’t pair a sub-heavy kick with a sub-heavy bassline, and shorten bass notes so they don’t play with the kick, which also buys headroom (Attack, “Ten production tips for better basslines”: Bass vs Kick).

  1. Draw the drums first. Then draw the sub notes into the gaps, starting them one or two 16ths after each kick.
  2. Where the sub must overlap a kick (a long held note), shorten the kick tail rather than ducking the sub hard.
  3. End sub notes 20–40 ms before the snare if the snare has body below 200 Hz; the tiny gap sharpens the snare on a system.
  4. Keep the sub’s amp envelope release at 20–40 ms (about one cycle at 41–49 Hz) so note ends do not click.
In 4/4 deep techno the kick is on every beat, so turn-taking happens inside the beat instead: the bass sits on the offbeat 8th, or the kick owns the sub range and the bass starts above 70–80 Hz. See Deep techno.

Grid-locked envelope ducking at 140 halftime

Device: Shaper (M4L), Utility, Compressor · Level: intermediate · Genres: deep dubstep, UK bass, deep techno

Quick start

Load
Shaper, Utility
Set
  • Shaper on the sub Rate 1 bar sync, before Utility
  • Map Utility Gain, −10 dB (min) to 0 dB (max); 6–10 dB is usually enough
  • Dip at each kick bottom in 3–5 ms, recover over 60–120 ms, curved
  • Recovery not shorter than ~40 ms on a 41 Hz sub
  • Utility Bass Mono 120 Hz
You should hear
A gentle, identical duck under every kick that clears its low end without a gap or a thump in the sub.
Live edition
Standard and up

When the sub does overlap the kick, a drawn curve is more predictable than an audio sidechain: identical every bar, no detector smear. The specific job here is the sub’s period: the duck must be gentle enough not to bend a 41–55 Hz cycle.

  1. On the sub track: Shaper before a Utility. Rate synced to 1 bar. Map to Utility Gain with a range of −10 dB (min) to 0 dB (max). On a sub, 6–10 dB is usually enough; deeper reads as a gap.
  2. Draw a dip at each kick position in the bar. Reach the bottom in 3–5 ms (the kick transient lands on a lowered sub) and recover over 60–120 ms with a curved segment.
  3. Recovery shorter than ~40 ms on a 41 Hz sub is under two cycles and tends to thump; listen on the sub stack or on good headphones at moderate level.
  4. For an audio-keyed alternative: Compressor on the sub, sidechain from the kick, sidechain EQ low-pass around 150 Hz, Attack 3–10 ms, Release 80–150 ms, Lookahead 1 ms so the duck starts with the kick, not after it.
ParameterValueWhy
Depth−6 to −10 dBClears the kick’s low end without leaving a hole
Fall3–5 msFast enough that the kick transient lands clean
Recovery60–120 ms at 140 BPMBack before the next 16th (107 ms) or the 8th (214 ms)
Compressor Lookahead1 msDuck begins with the kick rather than a millisecond late
Every other ducking method in Live (Glue Range, Auto Filter follower, Roar, ghost kicks) is on Sidechain & ducking.

The kick-to-sub hand-off: short kick body, sub carries the note

Device: Simpler, EQ Eight, Utility · Level: intermediate · Genres: deep dubstep, deep techno

Quick start

Load
Simpler, EQ Eight, Utility
Set
  • Kick: Simpler amp Decay 120–180 ms at 140 BPM
  • EQ Eight HP 48 dB 35 Hz, bell 60 Hz +2 dB Q 1.4
  • Utility Mono
  • Check kick mostly in the 65–280 Hz band; sub steady below it
You should hear
A short, punchy kick and a sustained sub reaching the floor as two clear events instead of one long boom.
Live edition
Standard and up

On a four-way rig the kick’s punch (60–120 Hz) can come from the bass bins while the sub note (35–60 Hz) comes from a separate infra or sub stack. Design the kick as a short, punchy event in the bass-bin band and let the sub own the sustained fundamental. The two then reach the floor as separate, clear events instead of one long boom.

  1. Shorten the kick: Simpler amp envelope Decay 120–180 ms at 140 BPM, or Fade Out on the clip. Long 808-style tails belong to other genres.
  2. EQ Eight on the kick: 48 dB low cut at 30–35 Hz so the kick does not compete with the sub below that.
  3. Check the kick alone on a rig split (see System split rack): it should read mostly in the 65–280 Hz bass-bin band.
  4. Then check the sub alone: mostly in the infra band, steady.

Headroom, DC and infrasonics

The low-end headroom budget

Device: Utility, Live’s meters · Level: essential · Genres: all three

Quick start

Load
Utility
Set
  • Sub track alone peaks −12 to −10 dBFS
  • Kick track alone −10 to −8 dBFS
  • LOW group (sub, kick, rumble) −8 to −6 dBFS; balance with Utility Gain, faders at 0
  • Full mix pre-master −6 to −4 dBFS, nothing on the master yet
You should hear
A low end that takes the biggest share of the headroom on purpose and still leaves real room on the master.
Live edition
Intro and up

In these genres the sub and kick use most of the peak budget. Two in-phase signals that each peak at −6 dBFS can peak at 0 dBFS together. Plan the low end first; everything above 200 Hz is comparatively cheap in peak terms.

StageStarting point (peak)Why
Sub track alone−12 to −10 dBFSA sine’s RMS is only 3 dB below its peak, so a sub is loud for its peak
Kick track alone−10 to −8 dBFSShort transient; sums with the sub only where they overlap
Low end together (sub + kick + rumble)−8 to −6 dBFSIf this already hits −3, the mix has no room for anything else
Full mix pre-master−6 to −4 dBFSLeaves a mastering chain or engineer real room
  1. Group the sub, kick and any rumble into one LOW group. Its meter is your low-end budget.
  2. Balance the sub against the kick on that group with Utility Gain on each track, faders at 0.
  3. Bring the other groups up around the low end, not the other way round.
  4. If the master peaks hot only when sub and kick overlap, fix the overlap (tuning, hand-off, duck), not the master.
General gain staging (instrument −12, groups −6) is on Loudness & limiting. What is specific here is that the low-end group gets the biggest share of the budget on purpose.

DC offset: find it, and remove it before anything non-linear

Device: Utility (DC), Roar, Redux · Level: intermediate · Genres: all three

Quick start

Load
Utility, Roar, Glue Compressor
Set
  • Spot it waveform off the centre line in Clip View, or clicks at faded clip edges
  • Utility DC on, before any compressor, saturator or limiter
  • Roar Shaper Bias +20%
  • After the distortion another Utility with DC on
You should hear
No change by ear, but limiting acts evenly on both sides of the waveform and clip edges stop clicking.
Live edition
Suite

DC offset is a constant shift of the waveform away from zero. It is inaudible on its own, but it uses up headroom on one side of the waveform, makes a limiter or clipper act unevenly on positive and negative peaks, and causes clicks where clips start and stop. In bass music it mostly comes from asymmetric saturation (Roar’s Shaper Bias, Redux’s DC Shift, some waveshaper settings), resampled audio, and hardware recorded through interfaces with an offset.

  1. Spot it: in Clip View the waveform sits visibly above or below the centre line, or the positive and negative peaks differ a lot on a symmetrical sound. Clicks at clip edges with fades already on are another sign.
  2. Fix it: Utility with DC on, placed before any compressor, saturator or limiter. The Ableton manual notes the DC filter only has an audible effect when non-linear processing comes after it.
  3. After asymmetric distortion (Roar Bias, Redux DC Shift), add another Utility DC straight after the distortion.
  4. For resampled or recorded audio with offset, a Utility DC on the track before you consolidate removes it for good.
An offset is not the same as an asymmetric waveform. A kick with a bigger positive than negative first peak is normal and should not be “fixed”; DC filtering only removes the constant part.

Infrasonic filtering that leaves a 41 Hz sub untouched

Device: EQ Eight · Level: essential · Genres: deep dubstep, deep techno

Quick start

Load
EQ Eight, Spectrum
Set
  • EQ Eight on sub, kick, rumble band 1, 48 dB low cut at 22–28 Hz
  • Slope 48 dB/oct, not 12
  • Check loop a sustained sub note; Spectrum (large Block, Max on) shows no change at the fundamental
  • If it changes lower the cutoff
You should hear
Rumble below the note gone, with an E0 sub at 41.2 Hz exactly as loud as before.
Live edition
Standard and up

Content below about 25–30 Hz moves cones and uses amplifier power while producing little a dancefloor can hear; many horn-loaded subs roll off steeply below their tuning. In genres whose sub root can sit at E0 (41.2 Hz), the filter must be steep, so it removes the rumble without touching the note.

  1. On the sub, kick and any rumble: EQ Eight band 1 as a 48 dB low cut at 22–28 Hz. EQ Eight’s cut filters are 12 or 48 dB/oct; use 48 here.
  2. Loop a sustained sub note and toggle the band: Spectrum (large Block, Max on) should show no change at the fundamental. If it does, lower the cutoff.
  3. Enable Oversampling in EQ Eight’s context menu only if you also use steep high bands; it does not matter for a 25 Hz cut.
  4. A gentle master low cut is then optional. Doing it per source means you know what each filter does.

Crest factor and loudness

Measure crest factor (PLR) instead of guessing loudness

Device: M4L loudness meter, Limiter · Level: intermediate · Genres: all three

Quick start

Load
Limiter
Set
  • Limiter Ceiling Mode True Peak, Ceiling −1 dB
  • Loudness meter (M4L) short-term LUFS and true peak on the loudest 16 bars, reset first
  • PLR short-term LUFS to true peak: −8 LUFS at −1 dBTP is 7 dB
  • References three records, level-matched, measured the same way
  • PLR well below them back off limiting first
You should hear
A number that tells you how much punch the master keeps, set against records that work on a system.
Live edition
Intro and up

Read two numbers on the drop: short-term LUFS and true peak. Their difference is the PLR. It tells you how much transient your master still has, which on a big rig is more useful than the loudness figure alone.

Drop short-term LUFSTrue peakPLRWhat it usually sounds like on a big rig (By ear)
−10−1 dBTP9 dBOpen; kick and snare jump; DJ trims it up a little
−8−1 dBTP7 dBCompetitive, still punchy if the low end is clean
−6−0.5 dBTP5.5 dBDense; snare loses its crack; sub sounds smaller
−5 or louder−0.3 dBTPunder 5 dBFlat; the system engineer often pulls it down
  1. Loop the loudest 16 bars. Reset the meter, read short-term LUFS once it settles, read the true-peak maximum.
  2. Do the same on three reference records you know sound right on a system, level-matched (see Reference tracks).
  3. If your PLR is several dB below the references, back off limiting first; the low-end fixes earlier on this page usually let you keep loudness with less limiting.
Documented: Rashad Becker of Dubplates & Mastering advises judging compression at matched average level rather than matched peaks, and calls maximising essentially pointless (RBMA lecture, Tokyo 2014; interview with Robert Henke). PLR is a quick way to put that into a number.

Clip above the sub, never the sub

Device: Audio Effect Rack, EQ Eight, Saturator · Level: advanced · Genres: deep dubstep, UK bass, deep techno

Quick start

Load
Audio Effect Rack, EQ Eight, Saturator, Glue Compressor
Set
  • Chain 1 (Low) EQ Eight LP 48 dB 120 Hz
  • Chain 2 (High) EQ Eight HP 48 dB 120 Hz
  • Null check nothing else in the chains: rack sounds the same as bypass; if hollow, split at 90–100 Hz
  • Chain 2 only Saturator Analog Clip, Soft Clip on, Drive +1 to +3 dB
  • Chain 1 gentle Glue 2:1, 1–2 dB, or nothing
You should hear
The kick click and snare get clipped for loudness while the sub stays a pure sine with no boxy buzz.
Live edition
Standard and up

Clipping a sine makes it squarer: it adds odd harmonics at 3×, 5×, 7× the note. On a 41 Hz sub those land at 124, 206 and 288 Hz, exactly in the bass bins and the low mids, where they turn into a boxy buzz at volume. Split the master (or the low group) so clipping only touches what is above the sub.

  1. Audio Effect Rack on the master (or LOW group) with two chains. Chain 1: EQ Eight 48 dB low-pass at 120 Hz. Chain 2: EQ Eight 48 dB high-pass at 120 Hz.
  2. With nothing else in the chains, check the rack sounds the same as bypass. Filter splits are not perfectly phase-flat; if the crossover region sounds hollow, move the split to 90–100 Hz where there is less content.
  3. Add Saturator (Analog Clip, Soft Clip on, Drive +1 to +3 dB) only to chain 2. The kick click and snare get clipped; the sub does not.
  4. Control the low chain with gentle Glue (2:1, 1–2 dB) or nothing.
Drum-bus clipping and limiter staging in general are on Loudness & limiting.

Two masters: one for DJs, one for streaming

Device: Limiter (Ceiling Mode), Utility · Level: essential · Genres: all three

Quick start

Load
Saturator, Limiter
Set
  • Saturator Analog Clip +1–2 dB
  • Limiter Ceiling Mode True Peak, Ceiling −1 dB, Lookahead 3 ms
  • DJ master Gain up until the drop matches your reference or the kick starts to flatten
  • Streaming master Limiter Gain 2–4 dB lower
  • Export both 24-bit, project sample rate, no normalise
You should hear
A louder DJ master and a streaming master that keeps more transient once it is turned down to −14.
Live edition
Intro and up

Make two exports from one mix instead of one compromise. The DJ master can be somewhat louder and have a slightly higher ceiling; the streaming master is made for loudness normalisation and lossy encoding.

TargetLoudnessCeilingSource / status
SpotifyNormalised to −14 LUFS integrated (Loud setting −11, Quiet −19)Below −1 dBTP; below −2 dBTP if the master is louder than −14 LUFSDocumented: Spotify for Artists
Apple MusicWidely reported as about −16 LUFS via Sound Check−1 dBTP is the common adviceSecondary sources only; Apple does not publish it as a delivery spec
General streaming guidanceAES TD1008 (2021) superseded TD1004TD1004 asked for encoded peaks no higher than −1 dBTPDocumented: summary at Production Advice
DJ master (deep dubstep, deep techno)Starting point: −10 to −8 LUFS short-term on the drop−1 dBTP (True Peak mode)Opinion; checked against references. No DJ standard exists
DJ master (UK bass roller)Starting point: −9 to −7 LUFS short-term−1 dBTPOpinion; rollers usually sit denser than deep dubstep
Vinyl or dubplateSet by the cutting engineerDeliver unlimited or lightly limited, −3 dBFS peaks or lowerAsk the cutting room; see below
  1. Build the master chain once. Save Limiter states with Live 12.3’s A/B compare, or as two device presets.
  2. DJ master: raise Limiter Gain until the drop reaches your reference’s short-term LUFS or until the kick starts to flatten, whichever comes first.
  3. Streaming master: lower Limiter Gain by 2–4 dB. It will be turned down to −14 anyway; the extra transient survives normalisation.
  4. Export both at 24-bit, sample rate matching the project, no normalise.
Do not publish a single “club” figure as if it were a standard. Engineers and labels disagree by several LU. Your references and your PLR are the honest guide.

Dubplates and cutting

What “cut for the system” meant, and what it means in Live now

Device: EQ Eight (M/S), Multiband Dynamics · Level: intermediate · Genres: deep dubstep, deep techno, UK bass

Quick start

Load
EQ Eight, Multiband Dynamics, Utility
Set
  • EQ Eight M/S mode, S low cut 48 dB at 120–150 Hz
  • Multiband Dynamics High band above 6 kHz: Above −20 dB, 3:1, Soft Knee
  • Utility peaks −3 dBFS, no limiter
  • Test A/B against the mix without the chain
You should hear
If the track gets worse through this chain, it depended on stereo lows or harsh tops a system will expose.
Live edition
Standard and up

Documented: a dubplate is a one-off acetate (lacquer) disc cut from a master so a DJ can play unreleased music. Cutting houses such as Music House and Transition had long Friday queues at their busiest (The Vinyl Factory). Jason Goz of Transition Mastering traces the practice to 1970s reggae sound systems; an acetate typically lasted about fifty plays, and a single plate cost around thirty to forty pounds (Clash, “Nuff Wheel Ups”). Mala has described cutting his first dub, Pathways, at Transition for Hatcha to play at FWD>>, and having to get each plate right first time because plates were expensive (Zweikommasieben, “Inside the DMZ”).

Cutting forced decisions that a USB stick does not. On a stereo groove, Mid (L+R) moves the stylus sideways and Side (L−R) moves it up and down. Loud out-of-phase bass means deep vertical motion, which can make the stylus skip or the cutter lift out. Loud, bright, noisy top end is hard for a DJ stylus to track. Engineers handled this with elliptical EQ (folding low Side to mono), band-selective compression and level. Documented: Bristol’s Dubstudio found that cutting about 6 dB quieter reduced skipping and distortion (The Vinyl Factory). Documented counterpoint: Rashad Becker calls the idea that bass must be mono for vinyl a myth and says he has had to cripple a stereo bass only a handful of times, preferring side-band control over full mono (Henke interview; RBMA).

Documented, from the scene itself (Lauren Martin, “The VICE Oral History of Dubstep”, 2015): Jason Goz describes keeping dub levels moderate so the music stayed dynamic, and names bass as his favourite element. Loefah recalls panning his basslines and being told the track would have to be cut mono, and says Goz asked questions about tightening the bass rather than dictating changes. Mala says sitting in on sessions taught him that some low frequencies do not translate to vinyl, and that rolling off the very bottom can make a track sound heavier. Oris Jay says plates were expensive enough that you made sure a tune was finished before cutting it. Pinch remembers Skream’s “Bahl Fwd” as one of the heaviest records because its bass was left without EQ at full power. These are memories of particular cuts, not a rulebook, and they sit alongside Becker’s view above.

  1. Even if you never cut, treat the old constraints as a test: run the pre-cut chain above and A/B. If the track gets worse, it depended on stereo lows or harsh tops that a system will expose anyway.
  2. Hats: long, noisy, loud hats are the hardest thing to cut and the harshest thing on horn-loaded tops. Becker notes short, tonal hats cut better (RBMA).
  3. Deliver to a cutting room with no limiter on the master and peaks around −3 dBFS or lower, unless the engineer asks otherwise. Their lathe and their ears set the level.
  4. Tell them where it will be played. “Please make it work on a club PA” is a real request Becker describes getting; the more you say about the rig and the record’s length, the better.
Documented: Dubplates & Mastering in Berlin is linked to Basic Channel’s founders and still keeps the label’s catalogue on vinyl (The Quietus). Becker also notes that a long record with late, bright hats can be cut so the top end falls on the outer grooves, where there is more groove speed (RBMA).
Further reading. Lauren Martin’s Aftershock: The Seismic Impact of Dubstep (Velocity Press, due 3 August 2026) is an oral history built from 28 interviews, covering FWD>>, DMZ, Hyperdub, Tempa, Skull Disco and the sound-system roots of the music (publisher’s page). Beatportal’s announcement names interviewees including Mala, Loefah, Kode9, Hatcha, Youngsta and Pinch, lists cutting houses and soundsystems among the places it covers, and says it expands on Martin’s 2015 VICE oral history of dubstep (Beatportal). This page has not drawn on the book’s contents; read it for the first-hand history of dubplates and the FWD>> and DMZ systems.

The test-on-the-system loop

Device: Arrangement, export · Level: essential · Genres: all three

Documented: Mala has said DMZ’s producers finished and mixed tracks, then tested them in the car, at home and on several systems before cutting (Zweikommasieben). The plate was the commitment; the tests came first. Today the cost of a test is a USB stick, so run the loop deliberately.

  1. Export the DJ master with a version number in the name. Put it between two references you trust in the set.
  2. On the system, listen from the booth, then from the middle of the floor, then near the sub stack. Note timestamps: “2:14 sub drops out on G”, “snare harsh at 3:00”.
  3. Back in Live, set locators at those times and fix only the top two or three problems. More changes per round and you cannot tell what helped.
  4. Do not judge the low end from the booth. Booth monitors often have little sub, and the booth may sit in a null of the room.

Live dub mixing in Live

Send throws: momentary sends into a tape-style echo

Device: Echo on a return, MIDI/key mapping · Level: essential · Genres: deep dubstep, deep techno, dub

Quick start

Load
Echo, Utility, Limiter
Set
  • Return A: Echo 3/16 L, 1/4 R, FB 55%, Filter on: HP 250 Hz, LP 3 kHz Res 15%
  • Echo Ducking Threshold −30 dB, Release 300 ms
  • Utility Bass Mono 150 Hz
  • Snare Send A mapped to a pad, Min −inf, Max about −6 dB
  • Limiter at the end of the return during performance
You should hear
One snare or stab thrown into echoes that stay out of the sub and off the horn tops, then die before the drop.
Live edition
Suite

A throw is a short burst of send on a single hit: a snare, a chord stab, the last word of a vocal. The echo carries on after the send closes. Live does this with a return track and a mapped send knob; the system-specific part is keeping the echo’s low end out of the sub feed and its repeats out of the 2–5 kHz horn region.

  1. Return A: Echo, Feedback 45–65%, Filter on with HP 200–300 Hz and LP 2.5–3.5 kHz. The HP keeps repeats out of the sub; the LP keeps them off the horn tops.
  2. Map the snare track’s Send A to a pad or key (Cmd/Ctrl+M or MIDI Map). In the mapping browser set Min to −inf and Max to about −6 dB.
  3. For a momentary throw, use a pad sending note on/off mapped to a Send knob range, or automate it in Arrangement as one-16th spikes.
  4. Ride the Echo Feedback live for build-ups, and pull it down hard at the drop so the tail does not cross the next downbeat.
A delay return feeding back at 80–100% builds energy below the HP slope too. Keep a Limiter at the end of the return during performance; runaway feedback on a big rig is loud very quickly.
Delay design in general is on Delay design, and the dub delay send rack is on Dub delay send rack.

Desk-style EQ kills on groups

Device: EQ Three, Push or MIDI controller · Level: essential · Genres: deep dubstep, deep techno, dub

Quick start

Load
EQ Three, Utility
Set
  • EQ Three on each group 48 dB slope (24 dB if you hear colouring)
  • Frequencies FreqLo 100–150 Hz, FreqHi 2–3 kHz
  • Low Kill Low band On/Off mapped to a pad
  • Drop kill the LOW group for the last bar, back exactly on the downbeat
  • Bass only kill Mid and High on MUSIC and DRUMS
You should hear
The bass vanishes from everything for a bar and slams back in on the one.
Live edition
Intro and up

Sound-system and dub mixing borrows from the preamp and the DJ mixer: cut the bass out of everything for a bar, then drop it back on the one. Documented: Channel One’s Mikey Dread describes the preamp, with its crossover and EQ, as the system’s brain (MusicRadar). In Live the equivalent is EQ Three on each group with its band gains mapped to buttons.

  1. EQ Three on each group, slope 48 dB for clean kills (the manual notes 48 dB colours the sound slightly even at 0 dB; use 24 dB if you hear it).
  2. FreqLo 100–150 Hz, so a low kill takes out the sub feed completely; FreqHi 2–3 kHz.
  3. Map the Low band On/Off to a pad. Kill the LOW group for the last bar before a drop, then drop it back exactly on the downbeat.
  4. For a dub-style “bass only” moment, kill Mid and High on MUSIC and DRUMS, leaving the sub and the kick.
EQ Three for DJ transitions is covered on EQ strategies; here the point is using kills as a performance instrument on the low group.

A dub siren from stock devices

Device: Operator or Analog, Echo · Level: intermediate · Genres: dub, deep dubstep

Quick start

Load
Operator, Auto Filter, Echo, Utility
Set
  • Operator one oscillator, Square or Saw; LFO to pitch, Amount 30–60%, Rate 2–8 Hz
  • Amp envelope Attack 5 ms, Sustain full, Release 300–600 ms
  • Auto Filter LP 24, 3 kHz
  • Echo 1/4, FB 50%, Wobble 20%
  • Utility Gain −12 dB
You should hear
A wailing (triangle LFO) or two-tone (square LFO) siren that tails off into the echo.
Live edition
Suite

The classic siren is a simple oscillator with an LFO on its pitch, triggered by hand and fed into an echo. Documented: sirens have long been used in sound-system clashes, including over a rival’s set (Dub-Stuy interview with Iration Steppas). On a big rig the siren is the loudest thing in the 1–3 kHz range, so filter it.

  1. Operator: one oscillator, Square or Saw waveform. Enable the LFO, destination pitch, Amount 30–60%, Rate 2–8 Hz. Triangle for a wail, Square for a two-tone.
  2. Map LFO Rate and the oscillator’s Coarse/Fine pitch to two knobs; the performance is in moving them.
  3. Amp envelope Attack 5 ms, Sustain full, Release 300–600 ms so the siren tails into the echo.
  4. Auto Filter LP at 2.5–3.5 kHz; Echo after it with Feedback 40–60%.

Spring reverb and tape-style echo, stock

Device: Hybrid Reverb (Convolution, Springs IRs), Echo (Noise, Wobble, Reverb Location) · Level: intermediate · Genres: dub, deep dubstep, deep techno

Quick start

Load
Hybrid Reverb, EQ Eight, Echo, Limiter
Set
  • Return B: Hybrid Reverb Routing Convolution, IR from Springs, Decay 70%, EQ low cut 300 Hz, Stereo 60%
  • Return B: EQ Eight HP 48 dB 250 Hz, LP 12 dB 5 kHz
  • Return A: Echo 3/16, FB 60%, Noise 15%, Wobble 25%, Reverb 20% Location Feedback
  • Echo Filter HP 200 Hz, LP 2.8 kHz; Limiter Ceiling −3 dB
  • Sends snare to B in short throws; chords and vocal ends to A
You should hear
A spring crash on snare throws and tape-like echoes whose space builds with every repeat.
Live edition
Suite

Hybrid Reverb’s Convolution IR menu has a Springs category; Echo has Noise and Wobble to imitate tape, and can place its own reverb inside the feedback loop. Together they give the spring-and-tape dub return. By ear: echo, spring and siren around a single deck is the classic roots sound-system palette; the specific units any given system uses are not documented here.

  1. Return B: Hybrid Reverb, Routing set to Convolution, pick an IR from Springs. Use its EQ (or EQ Eight after) to remove everything under 250–300 Hz.
  2. Return A: Echo with Noise and Wobble on at low Amounts; set Reverb Location to the feedback loop so the space builds with each repeat.
  3. Send the snare to B in short throws for the spring crash; send chords and vocal ends to A.
  4. Route Return A to Return B a little (enable return-to-return sends in the send’s context menu) for echoes that land in the spring.

Checking translation

System split rack: hear what each box of the rig gets

Device: Audio Effect Rack, EQ Eight · Level: intermediate · Genres: all three

Quick start

Load
Audio Effect Rack, EQ Eight, Utility
Set
  • Infra chain EQ Eight HP 48 dB 25 Hz, LP 48 dB 65 Hz; Utility Mono
  • Bass bins chain HP 48 dB 65 Hz, LP 48 dB 280 Hz; Utility Mono
  • Mids chain HP 48 dB 280 Hz, LP 48 dB 5 kHz
  • Tops chain HP 48 dB 5 kHz
  • Band macro Chain Selector 0 → 3, one chain at a time
You should hear
Each box of the rig in turn: a steady infra band, the groove in the bass bins, a track that holds up on mids and tops.
Live edition
Standard and up

A four-way club rig splits your mix into bands that may sit in different boxes and positions. Audition each band alone and the problems become obvious: a groove that only exists in the sub band, a kick with no bass-bin energy, a bass whose character is all above 280 Hz.

  1. Audio Effect Rack on the master with four chains, frequency bands as above. Give each chain one Chain Selector zone and map the selector to Macro 1.
  2. Infra only: should be steady, in tune and in time. If it is empty, your sub is above 65 Hz.
  3. Bass bins only: this is where the kick punch and most of the bass note harmonics live. The groove should already be recognisable here.
  4. Mids and tops: should carry the track on their own. If the track collapses without the lows, it will collapse for anyone standing near the tops and far from the subs.

Make the sub read on small speakers without adding system mud

Device: Audio Effect Rack, Saturator, EQ Eight · Level: intermediate · Genres: deep dubstep, UK bass

Quick start

Load
Audio Effect Rack, Utility, Saturator, EQ Eight
Set
  • Clean sub chain Utility Bass Mono 120 Hz, 0 dB
  • Harmonics chain Saturator Soft Sine, Drive +12 dB
  • Harmonics: EQ Eight HP 48 dB 150 Hz, LP 12 dB 1.5 kHz
  • Harmonics level start at −24 dB, raise on a phone until the sub line can be followed
You should hear
The sub line becomes followable on a phone while the bass-bin band of the rig barely changes.
Live edition
Standard and up

A pure sine sub is invisible on a phone and perfect on a rig. Adding harmonics helps the phone and can hurt the rig, because the 2nd and 3rd harmonics of a 41–55 Hz note sit in the bass bins (82–165 Hz). The compromise: a parallel chain that only adds harmonics from about 150 Hz up, where small speakers start working.

  1. Rack on the sub: chain 1 dry; chain 2 Saturator Soft Sine with high Drive, then EQ Eight HP at 150 Hz (48 dB) and LP around 1.5 kHz.
  2. Set chain 2 volume very low (−24 dB) and raise it while listening on a phone until the sub line can be followed.
  3. Check on the System split rack: the bass-bin band should not change much when you toggle chain 2.
General phone, earbud and car simulations are on the Listening checklist.

Reference tracks: compare the sub and the tops separately

Device: Utility, EQ Eight, Spectrum · Level: essential · Genres: all three

Quick start

Load
Utility, EQ Eight, Spectrum
Set
  • Reference track Audio To the main out; Utility trim to your drop's short-term LUFS
  • EQ Eight LP 48 dB 100 Hz for sub only, HP 48 dB 100 Hz for no sub; Macro 1 switches
  • Spectrum Avg slow, Max on
  • Sub only compare level and steadiness of the note
  • No sub compare energy and groove
You should hear
Whether your sub is as heavy and steady as the reference, and whether the track still drives without it.
Live edition
Standard and up

Level-matched referencing is covered elsewhere. For a system, compare in two bands: below 100 Hz (is my sub as heavy and as steady?) and above 100 Hz (does my track still have the same energy when you take the sub away?). The second check matters because much of a big crowd hears mostly tops.

  1. Route the references around the master chain. Trim each to your drop’s short-term LUFS.
  2. Group the reference track and a copy of your mix into a rack with the same EQ Eight. Macro 1 switches between “sub only” and “no sub”.
  3. Sub only: compare the level and steadiness of the note; use Spectrum’s Max hold to see the peak level of the fundamental on both.
  4. No sub: compare energy and groove. If your track feels empty here and the reference does not, the mid-bass and drums need work, not the sub.

Club PA realities

Sub crossovers, bass bins and horn-loaded tops

Device: none (knowledge) · Level: essential · Genres: all three

Systems differ, but a few facts are useful. Many club systems hand the subs over to the tops somewhere around 80–120 Hz, so the band your kick punch lives in may be split between two kinds of box. Four-way systems split lower. Documented: Funktion-One’s Dance Stack is four-way with 24 dB/oct crossovers: an infrabass section for 20–65 Hz, a hybrid horn-loaded 15 inch for 65–280 Hz, a 10 inch mid to 5 kHz and a compression driver above (LSi).

  • Horn-loaded boxes are efficient and directional. At high level the 1–5 kHz region of a horn-loaded mid or top can be piercing on axis. Snare cracks, hats and dub sirens are what get you there first.
  • Subs and tops are often physically apart. System engineers time-align them, but only for some positions. A kick with its punch and its sub in two bands that you have already designed to work separately survives misalignment better.
  • System processors have limiters. Documented: Mark Iration describes the move from many 100–200 W speakers and amplifiers to 2,000 W speakers on single Powersoft amplifiers configured by computer and monitored for over- or under-performance (Band on the Wall). Modern rigs watch what you feed them.
  • Some rooms let sparse tracks work. Documented: in Martin’s VICE oral history, Kode9 says the FWD>> system at Plastic People let producers get away with very sparse, heavy tracks that would not have worked on other systems, and Joe Nice remembers DMZ at Mass in Brixton as a high-ceilinged room with bass-heavy rigs and no limiters (VICE, 2015). Do not assume the rig you play on is that forgiving: check your mix on the system split rack.

Room modes and why one note booms

Device: Spectrum, Tuner · Level: intermediate · Genres: deep dubstep, deep techno

Quick start

Load
Spectrum, EQ Eight
Set
  • Spectrum Max hold while the bassline plays
  • Loud note lower its velocity or clip gain, or a narrow EQ Eight bell
  • Long single-pitch notes avoid around 49 Hz unless the boom is the point
  • Your studio if one note jumps on monitors but not headphones, trust the meter
You should hear
A sub line with every note at an even peak level, so no single pitch booms in a resonant room.
Live edition
Standard and up

A room resonates at frequencies set by its size: the first axial mode of a dimension is 343 ÷ (2 × length) Hz, then whole-number multiples. A 7 m wide basement resonates near 24.5, 49 and 73.5 Hz; a 3.5 m ceiling near 49 Hz. In such a room a G0 (49 Hz) sub note booms and an E0 (41 Hz) may vanish in places. You cannot mix for every room, but you can avoid making it worse.

Dimension1st mode2nd3rd
3.5 m (ceiling)49.0 Hz98.0 Hz147 Hz
7 m24.5 Hz49.0 Hz73.5 Hz
10 m17.2 Hz34.3 Hz51.5 Hz
15 m11.4 Hz22.9 Hz34.3 Hz
  1. Even out the sub line before it reaches any room: Spectrum with Max hold while the bassline plays; if one note’s peak is several dB above the others, lower that note’s velocity or clip gain, or tame it with a narrow EQ Eight bell.
  2. Avoid long sustained notes on a single pitch that a common room size reinforces (around 49 Hz is a frequent one in small, low-ceilinged clubs) unless the boom is the point.
  3. Your own studio has modes too. If one note jumps on your monitors but not on headphones, it is probably your room. Trust the meter and the headphones for that note.

Dynamic control of the horn region

Device: Multiband Dynamics · Level: advanced · Genres: all three

Quick start

Load
Multiband Dynamics, Limiter
Set
  • Multiband Dynamics Low band off, Mid–High crossover 2.5 kHz
  • High band Above −24 dB, 2:1, Soft Knee, RMS
  • Timing Attack 5 ms, Release 80 ms
  • Threshold 1–2 dB off the snare crack only
You should hear
The snare and hats lose their piercing edge only when they hit hard, while the track keeps its brightness.
Live edition
Standard and up

A static cut at 3 kHz dulls the whole track. A dynamic one only acts when the snare, hats or a distorted bass push the horn region hard, which is when it hurts on a big rig.

  1. Multiband Dynamics on the master (or the drum group), Low band switched off, crossover at 2–3 kHz.
  2. High band, Above threshold, ratio 2:1, Soft Knee on, RMS. Lower the threshold until it takes 1–2 dB off the snare crack only.
  3. If one source causes it every time, put the same device on that source instead.

Mastering chains for these genres

Deep dubstep master chain (DJ version)

Device: EQ Eight, Utility, Audio Effect Rack, Glue Compressor, Limiter · Level: advanced · Genres: deep dubstep

Quick start

Load
Utility, EQ Eight, Audio Effect Rack, Glue Compressor, Limiter
Set
  • Utility DC on
  • EQ Eight 48 dB low cut 25 Hz; M/S: Side low cut 48 dB 140 Hz
  • Clip Above Sub rack split 110 Hz, Analog Clip +1–2 dB on the high chain
  • Glue Compressor 2:1, Attack 10 ms, Release Auto, 1 dB
  • Limiter Gain +2–3 dB, True Peak, Ceiling −1 dB, Lookahead 3 ms
You should hear
A spacious master with a clean sub and a loud snare, around −10 to −8 LUFS short-term on the drop.
Live edition
Standard and up

Deep dubstep is mostly space: a sub, a kick, a snare, sparse percussion and reverbs. The master should protect that space. Keep the sub clean, let the snare stay loud, and use very little limiting.

StageSettingWhy
Utility DCOnRemoves offset before the clipper and limiter
EQ Eight25 Hz 48 dB; Side low cut 140 HzInfrasonics out; low Side folded
Clip rackSplit ~110 Hz, +1–2 dBSnare and kick click clipped, sub untouched
Glue2:1, 10 ms, Auto, ~1 dBLight glue, not loudness
LimiterTrue Peak, −1 dB, 3 msSafety ceiling with a little gain
Result (starting point)−10 to −8 LUFS short-term on the drop, PLR 7–9 dBOpinion; check against references

Deep techno master chain (DJ version)

Device: EQ Eight, Multiband Dynamics, Saturator, Limiter · Level: advanced · Genres: deep techno, dub techno

Quick start

Load
EQ Eight, Multiband Dynamics, Saturator, Limiter
Set
  • EQ Eight 48 dB low cut 25 Hz; M/S: Side low cut 48 dB 150 Hz
  • Multiband Dynamics Low below 120 Hz, Above 2:1, Time 100 ms, 1–2 dB
  • Saturator Analog Clip +1 dB, Soft Clip on
  • Limiter Gain +2–3 dB, True Peak, Ceiling −1 dB, Release Auto
  • Check a 32-bar blend with a reference, both kicks running
You should hear
An even master whose low end sums cleanly with another record's kick during a long blend.
Live edition
Standard and up

Deep techno runs long at a steady level. DJs blend it for minutes at a time with another track, so its low end has to sum cleanly with someone else’s kick. Keep the rumble controlled, the kick tail short of the next beat, and the master even.

  1. Multiband Dynamics low band: crossover just above the kick fundamental (100–150 Hz), Above threshold 2:1, Time around 100 ms (faster than the 469–484 ms beat at 124–128 BPM, slower than a 20 ms sub cycle).
  2. Saturator only for 1 dB of peak shaving; deep techno kicks are usually rounded already.
  3. Check a 32-bar DJ blend: put a reference deep techno record on another track, overlap the two intros with both kicks running, and listen for a low end that doubles to a boom (two kicks tuned differently) or cancels.

UK bass roller master chain

Device: Roar (Multi Band), Glue, Limiter · Level: advanced · Genres: UK bass, 140 rollers

Quick start

Load
EQ Eight, Roar, Glue Compressor, Limiter
Set
  • EQ Eight 48 dB low cut 25 Hz; M/S: Side low cut 48 dB 160 Hz
  • Roar Multi Band: low stage clean (Amount 0), Mid/High Soft Sine 2–3 dB, Blend 40%
  • Glue Compressor 2:1, Attack 3 ms, Release Auto, 1–2 dB
  • Limiter Gain +3–4 dB, True Peak, Ceiling −1 dB
You should hear
A denser master where the mid-bass and drums carry the saturation and the sub stays clean.
Live edition
Suite

Rollers are denser: a constant mid-bass, 2-step drums, more top. They can take more density, but the same rule applies: the sub stays clean while the mid-bass and drums get the saturation.

  1. Roar in Multi Band routing: leave the low stage clean (Amount 0), drive mid and high stages lightly, Blend 30–50%.
  2. Check the System split rack: the infra band should look identical with Roar on and off.
  3. Rollers typically land 1–2 LU louder than deep dubstep at similar PLR because the mid-bass is constant (By ear).
The mid-bass layer itself is on Bass music mid-bass; the track walkthrough is on UK bass roller track.

Preparing files for DJs

DJ-ready edits, dubs and stems

Device: Arrangement, Export Audio/Video · Level: essential · Genres: all three

A track that is easy to mix gets played more. For a sound system that means a clean drum intro, an outro that can be blended for 16–32 bars, a version without the vocal or lead for dub-style mixing, and stems for DJs who perform with them.

  1. Intro: 16 or 32 bars of drums with no sub and nothing tonal that clashes; the DJ will be playing another track’s low end over it.
  2. Outro: mirror of the intro. Let delay and reverb tails die before the last bar so the file ends clean.
  3. Dub version: export with the lead or vocal muted and the throws still on the returns. Sound-system DJs often play the vocal, then the dub.
  4. Stems: solo groups (LOW, DRUMS, MUSIC, FX) and export with File > Export Audio/Video, Rendered Track set to the individual tracks. Leave the master chain off the stems; they should sum back to the unmastered mix.
  5. Export the DJ master at 24-bit, at the project’s sample rate, with BPM and key in the file name (for example “Title_140_Fmin_DJ.wav”).
  6. Keep the tempo constant, with no tempo automation, so beat grids hold for the whole track.
Name stems by role, not by sound (“LOW”, not “Big Reese 3”), and include a text note with the BPM, key and bar count.

Genre recipes

DecisionDeep dubstep (140 halftime)Deep techno (124–128)UK bass roller (140)
Who owns 35–60 HzThe subThe kick, or kick and bass alternatingThe sub
Sub roots (By ear)E0–G0 (41–49 Hz)Bass often above 55 Hz; kick tail 45–60 HzE0–A0 (41–55 Hz)
Bass MonoSub 100–120 HzKick mono; rumble 120–150 HzSub 100–120 Hz; mid-bass 150–200 Hz
Kick/sub methodArrangement first, light drawn duckShort kick tail, offbeat bass, follower or Glue duckDrawn duck plus mid-bass filter duck
Infrasonic cut48 dB at 22–25 Hz48 dB at 25–28 Hz48 dB at 25 Hz
ClippingAbove the sub only, 1–2 dB1 dB on the master, kick rounded at sourceAbove the sub, 2–3 dB, Roar Multi Band
DJ master starting point−10 to −8 LUFS short-term, PLR 7–9−10 to −8 LUFS short-term, PLR 7–9−9 to −7 LUFS short-term, PLR 6–8
Dub toolsThrows, spring, siren, low killsLong echo returns, filter rides, low killsThrows, low kills
WalkthroughDeep dubstep trackHypnotic techno trackUK bass roller track

Drums for each style are on Deep dubstep drums and Hypnotic techno percussion; the sub itself is on Deep dubstep bass and Sub bass.

Pre-system checklist

  1. Side-solo check below 150 Hz is close to silent.
  2. Kick tail and sub roots are on key (Tuner, Spectrum semitone scale).
  3. Polarity checked for every overlapping low pair.
  4. LOW group peaks no higher than −6 dBFS before the master.
  5. Utility DC before every non-linear stage that follows asymmetric saturation; 48 dB infrasonic cut on low sources.
  6. No clipping below ~110 Hz.
  7. PLR on the drop measured and compared with references.
  8. System split: groove recognisable in the bass-bin band alone, and the track survives without the infra band.
  9. Horn region checked loud for a short time; snare and hats not piercing.
  10. Two masters exported (DJ and streaming), 24-bit, True Peak ceiling.
  11. DJ intro and outro clean; dub version and stems exported if wanted.
  12. Played on a real system from three positions before release.

Common mistakes

Sources

Related