ABLETON 12 SOUND DESIGN ATLAS

Sampler-Era Sound Design — Trip-Hop, Big Beat & Jungle Textures

The sample-based sound design of 90s trip-hop, big beat and jungle rebuilt in Live 12: what the Akai S950/S1000/S3000, E-mu SP-1200 and Emulator II and Ensoniq EPS/ASR-10 actually did to sound, the memory maths that forced short, pitched-up samples, and stock-device recipes for melodic chops, stabs, found strings, dust, scratches, reversed and pitched tails, filtered loops, layered pads, spring sends, turntable-speed tricks and loop-to-instrument resampling.

Difficulty
Intermediate
Live edition
Suite
Max for Live
Not needed

Between roughly 1987 and 1998 the sound of three genres was set as much by the sampler as by the records being sampled. Memory was measured in seconds, so loops were short and samples were taken sped up and played back down; converters were 12-bit or companded 8-bit, so quiet tails went grainy; filters were fixed circuits with their own personalities; and the timestretch algorithms were rough enough that their artefacts became a style of their own. This page is the era-specific layer on top of the generic material elsewhere on the site: the general bit/rate recipes live in Tape, lo-fi and analog character (including a short sampler emulation overview), the instruments themselves in Sampler, Simpler and Drum Rack, and the genre frames in Trip-hop and downtempo, Breaks and big beat, Jungle, Lo-fi hip-hop and Boom bap. Here we go machine by machine using documented specifications only, and then technique by technique for the melodic and textural side of the sampler (breaks get their own pages). Tempo references: at 90 BPM a bar is 2667 ms and a 1/16 is 167 ms; at 120 BPM a bar is 2000 ms; at 165 BPM a bar is 1455 ms and a 1/16 is 91 ms. Claims about how specific records were made are marked Documented with a link, or By ear.

Anatomy

The machines, by documented spec

Machine (year)BitsSample rateMemoryFilterSource
E-mu Emulator II (1984)8-bit, DPCM companded~27.7 kHz512 KB–1 MBSSM2045 4-pole 24 dB/oct resonant LPWikipedia: E-mu Emulator
Akai S900 (1986)12-bitvariable, ~7.5–40 kHz768 KiB for samplesanalogue LP (type not documented there)Wikipedia: Akai S900/S950
E-mu SP-1200 (1987)12-bit linear26.04 kHz10 s total, 2.5 s max per soundch 1–2 dynamic SSM2044, three fixed LP pairs, ch 7–8 unfilteredWikipedia: SP-1200
Ensoniq EPS (1988)13-bitnot documented there256 Kwords, expandablenot documented thereWikipedia: Ensoniq EPS
Akai S950 (1988)12-bit7.5–48 kHz750 KB, expandable to 2.25 MBlow-pass; specification not published in the sources readZoeblade S950 notes (Akai catalogues)
Akai S1000 (1988)16-bit44.1 kHz (22.05 kHz option)2 MB standard, later up to 32 MBdigital 18 dB/oct, non-resonantWikipedia: Akai S1000
Ensoniq ASR-10 (1992)16-bit29.76 or 44.1 kHz2 MB, expandable to 16 MBonboard effects (50–62)Wikipedia: ASR-10
Akai S3000 (1993)16-bit44.1 kHzexpandable to 32 MBresonant filters added, 32 voicesMusic Technology, 1993 preview
Documented users relevant to this page: Geoff Barrow used an S1000 and Adrian Utley an S950 around Dummy (Sound On Sound, June 1995); DJ Shadow composed Endtroducing..... almost entirely on an Akai MPC60 MkII (Wikipedia, citing Keyboard 1997); Norman Cook worked on an S900 and then S950s with an Atari ST (SOS Classic Tracks, January 2017); Rob Playford moved from the S950 to the S1000, S1100 and S3200 (Sound On Sound, June 1998). Where a page or forum names a different model for a given record, treat it as unresolved.

Recipes

The memory maths: why everything was one bar long

Planning · Level: essential · Genres: trip-hop, big beat, jungle, boom bap

Quick start

Load
Simpler, Drum Rack
Set
  • Budget eight sounds, none longer than 2.5 s, total under 10 s
  • Simpler Classic, Warp off, Start and Length dragged so each sound fits
  • Drum Rack one sound per pad, 8–12 pads total
  • Remaining pads single hits cut from the same record, not new sources
You should hear
Short material repeated and varied by muting and filtering: a coherent, era-correct arrangement cut from a handful of sounds.
Live edition
Intro and up

Before any device, understand the budget, because it explains the arrangement style. The SP-1200 allowed 2.5 seconds per sound and 10 seconds in total (Documented, Wikipedia). At 90 BPM one bar lasts 2667 ms, so a one-bar loop simply did not fit at original speed. The documented workaround was to play the record faster while sampling, then pitch it back down on playback, which used less memory per second of music (Documented, same source). On a 16-bit sampler the numbers are kinder but still finite: 2 MB of mono 16-bit audio at 44.1 kHz holds 2,097,152 ÷ 88,200 ≈ 23.8 s, or 11.9 s in stereo, 47.6 s at 22.05 kHz (by calculation).

BudgetAt 90 BPMAt 120 BPMAt 165 BPM
2.5 s (SP-1200 per sound)0.94 bar1.25 bars1.72 bars
2.5 s sampled at 45 from 33⅓ (×1.35)1.27 bars of source1.69 bars2.32 bars
10 s (SP-1200 total)3.75 bars for everything5 bars6.9 bars
23.8 s (2 MB, mono, 44.1 kHz)8.9 bars11.9 bars16.4 bars
  1. Set a budget for the track: for example eight sounds, none longer than 2.5 s, total under 10 s. Write it on a clip name so you keep to it.
  2. In Simpler (Classic, Warp off) drag Start and Length so each sound fits. If a loop is too long at your tempo, see the next recipe: sample it faster, play it back slower.
  3. Fill the remaining pads with single hits cut from the same record rather than new sources: era records sound coherent because everything came off a handful of discs.
Live has no memory limit, so the discipline is a choice. It is still the single most effective way to get era-correct arrangements: short material repeated, varied by muting and filtering.

Sample at 45, play at 33: the speed-up/pitch-down trick, with exact ratios

Instrument: Simpler, clip Re-Pitch · Level: essential · Genres: boom bap, trip-hop, jungle, big beat

Quick start

Load
Redux, Simpler
Set
  • Source clip Warp off, Transpose +5, Detune +20 ct (or Re-Pitch, tempo ×1.35)
  • Redux Rate 26 kHz, Bits 12, filters off, Jitter 0
  • Resample into a new audio track, Post FX
  • Simpler Classic, Warp off, Transpose −5, Detune −20 ct
You should hear
The loop back at its original pitch and tempo, but darker and grainier, its top now ending around 9.6 kHz.
Live edition
Intro and up

The tape page's sampler-emulation recipe uses a generic +12; the era's real ratio was the turntable's: a 33⅓ record played at 45 runs 1.35× faster, which is +5.20 semitones. Played back down, the sample returns to pitch and every artefact of the low-rate capture is transposed down with it, darker and grainier (the SP-1200 page attributes the "gritty" character partly to this drop-sample pitch shifting, Documented, Wikipedia). Documented: sampling a 33⅓ record at 45 bought extra sampling time from a few kilobytes, and pitching it down afterwards also lowered the aliasing (Sound On Sound, SampleX review).

Speed changeRatioSemitonesSimpler correction
33⅓ → 45 rpm1.35+5.20 stTranspose −5, Detune −20 ct
45 → 33⅓ rpm0.741−5.20 stTranspose +5, Detune +20 ct
Pitch fader +8%1.08+1.33 stTranspose −1, Detune −33 ct
Pitch fader −8%0.92−1.44 stTranspose +1, Detune +44 ct
Octave (tape ×2)2.0+12 stTranspose −12
  1. Put the source on an audio track. Either set Warp to Re-Pitch and raise the clip's tempo by 35% (the clip plays 1.35× faster and higher, Live 12 manual: Re-Pitch), or switch Warp off and set clip Transpose +5, Detune +20 ct.
  2. Insert Redux: Rate 26 kHz (SP-1200-like), Bits 12, pre/post filter off for aliasing, Jitter 0.
  3. Resample into a new audio track (Audio From: the source track, Post FX). Drag the result into Simpler, Classic, Warp off.
  4. Simpler Transpose −5 and Detune −20 ct: the loop is back at its original pitch and tempo, and the 13 kHz Nyquist ceiling of the capture has become ~9.6 kHz (13.02 kHz ÷ 1.35).
  5. For darker still, capture at +12 and play at −12: the effective ceiling falls to 6.5 kHz.
Do not do this with Warp on in Simpler. Warp keeps the duration constant and changes only pitch, which undoes the whole point: the artefacts must move with the speed.

SP-1200 voicing: 26.04 kHz, 12-bit and the eight different outputs

Instrument: Drum Rack, Simpler · Level: advanced · Genres: boom bap, trip-hop, big beat

Quick start

Load
Drum Rack, Simpler, Redux, Auto Filter, EQ Eight
Set
  • Drum Rack four chain groups, Simpler One-Shot or Classic, Warp off
  • Redux on every chain: Rate 26 kHz, Bits 12, filters off, Jitter 0
  • Out 1–2 Auto Filter Low-pass, MS2, cut-off around 2 kHz, Resonance 20%, driven upward on each hit
  • Out 3–6 EQ Eight high cut 48 dB at a different frequency per pair (8 kHz, 11 kHz)
  • Out 7–8 nothing after Redux
You should hear
A kit where each output pair has its own tone, from a moving filtered kick to darker snares and freely aliasing hats.
Live edition
Standard and up

The detail most emulations miss: the SP-1200's outputs did not all sound the same. Channels 1 and 2 ran through dynamic SSM2044 filters, other pairs through fixed low-pass filters at successively higher frequencies, and channels 7 and 8 were unfiltered (Documented, Wikipedia). Which output a sound was patched to was a tone choice. The exact cut-off frequencies are not published in the sources read, so the values below are by ear.

  1. Drum Rack, four chain groups as above. In each, Simpler One-Shot (drums) or Classic (pitched hits), Warp off.
  2. Redux on every chain: Rate 26 kHz, Bits 12, filters off. Live's Redux gives Rate, Jitter, Filter (pre/post) and Bits/Shape/DC Shift (manual); leave Jitter at 0 for a clock-steady machine.
  3. Out 1–2: Auto Filter, Low-pass, MS2 circuit, cut-off around 2 kHz, Resonance 20%, its envelope follower or an LFO in one-shot shape driving cut-off upward on each hit.
  4. Out 3–6: EQ Eight high cut 48 dB at different frequencies per pair. Out 7–8: nothing after Redux; hats there alias freely, which is the point.

S900/S950: variable rate per sound and the alternating loop

Instrument: Sampler, Simpler · Level: intermediate · Genres: big beat, trip-hop, early jungle

Quick start

Load
Sampler, Redux
Set
  • Sampler Sustain Mode Back-and-Forth, a loop of 80–200 ms on the steadiest part of a held note
  • Release Mode on, so the note plays out to Sample End
  • Redux one per sound, Bits 12; Rate 10–15 kHz for bass, 20–26 kHz for chords, 40–48 kHz for hats
  • Filter LP 12, Clean, no resonance, key tracking 50%, cut-off 5–8 kHz
You should hear
Each sound darkened by its own rate, held notes sustaining on a forwards-backwards loop and ending on their real decay.
Live edition
Suite

The S900 and S950 were 12-bit with a variable sample rate (S900 up to about 40 kHz, S950 up to 48 kHz), and the S900 could loop alternately forwards and backwards, a feature the S1000 series lacked (Documented, Wikipedia). Variable rate meant every sound got its own rate according to how much memory it deserved: a bass note at 15 kHz, a hi-hat at the top rate. That per-sound choice, rather than one global "lo-fi" setting, is the S950 texture.

SoundRedux RateBitsReason
Bass note / sub hit10–15 kHz12No content above 5 kHz worth memory
Rhodes / string chord20–26 kHz12Warm, top naturally gone
Vocal phrase26–32 kHz12Keep sibilance just about intact
Hats, cymbals40–48 kHz12The only sounds that needed full rate
  1. Sampler, Sample tab: set Sustain Mode to Back-and-Forth Sustain Loop (Live 12 manual: playback reverses at each loop boundary). Put a loop of 80–200 ms on the steadiest part of a held note.
  2. Release Mode on, so the note plays out to Sample End after key-up: the tail is the real decay, the sustain is the loop.
  3. Redux after Sampler with the rate from the table; one Sampler per sound so each can have its own rate.
  4. Filter LP 12, Clean circuit, no resonance, key tracking 50%. Cut-off open-ish (5–8 kHz) for most sounds: the darkness comes from the rate.

S1000: clean 16-bit, the 18 dB non-resonant filter and the darker truth

Instrument: Simpler, Sampler · Level: intermediate · Genres: trip-hop, big beat, jungle

Quick start

Load
Simpler, EQ Eight, Utility
Set
  • Simpler Classic, Warp off
  • Filter LP 12, Clean circuit, Resonance 0
  • Cut-off where the source goes behind a curtain, typically 2.5–5 kHz
  • EQ Eight high shelf 6 kHz −6 dB
  • Utility Mono
You should hear
A clean 16-bit sound whose top is removed completely, with no resonant bump to give it away.
Live edition
Standard and up

The S1000 was a 16-bit, 44.1 kHz machine with a digital 18 dB/octave, non-resonant filter (Documented, Wikipedia). That makes it the "clean" sampler of the era, and it is a mistake to bitcrush S1000-style material. Its character is that filter: steep enough to remove a record's top completely, without any resonant bump to give it away. Live has 12 and 24 dB slopes in Simpler; a 12 dB low-pass plus an EQ Eight high shelf approximates the in-between slope (by ear).

  1. Simpler Classic, Warp off. Filter LP 12 in the Clean circuit (Simpler offers Clean, OSR, MS2, SMP and PRD), Resonance 0.
  2. Set cut-off by ear to where the source "goes behind a curtain", typically 2.5–5 kHz for a string or Rhodes loop.
  3. EQ Eight high shelf above the cut-off for the steeper slope. Mono it: S1000 sounds were usually sampled mono to halve memory.
Documented: Geoff Barrow used an S1000 in the Dummy period (SOS 1995), and the S1000 page lists Portishead, Tricky, The Chemical Brothers and The Prodigy among users. That does not tell us which records used which machine; the dirt on those records came largely from the vinyl and the processing (see pressing your own sample).

S3000: when resonance arrived, and the filter-envelope stab

Instrument: Simpler · Level: intermediate · Genres: big beat, jungle, late-90s trip-hop

Quick start

Load
Simpler, Saturator, Echo
Set
  • Simpler a single stab, Classic, Warp off
  • Filter LP 12 Clean, Res 45%, Freq 600 Hz, Env +55%
  • Filter envelope A 0, D 220 ms, S 0.2, R 120 ms
  • Velocity Simpler's Vel control → filter envelope amount
  • Saturator Analog Clip, Drive 4 dB
You should hear
A squelchy sampled stab swept like a synth oscillator, opening further on accents.
Live edition
Suite

The 3000 series added resonant filters and 32-voice polyphony (Documented, Music Technology, 1993); later S3000XL literature describes a −12 dB/octave low-pass with resonance. That opened the door to treating a sample like a synth oscillator: a resonant envelope sweep on a horn stab or a Rhodes chord, the "squelchy" sampled stab of big beat and late jungle.

  1. Load a single stab (horn, organ chord, Rhodes chord) in Simpler Classic, Warp off.
  2. Filter LP 12 Clean, Resonance 40–50%, cut-off 500–800 Hz, Envelope amount +50–60%, filter envelope as shown.
  3. Map velocity to the filter envelope amount (Simpler's Vel control in the filter section) so accents open further.
  4. Play the stab at three pitches only (root, minor 3rd, 5th) so the resonance never sits on a clashing harmonic.

Emulator II: companded 8-bit and the 24 dB resonant filter

Instrument: Sampler · Level: advanced · Genres: trip-hop, cinematic downtempo

Quick start

Load
Sampler, Compressor, Redux, Auto Filter
Set
  • Sampler strings or choir multisample
  • Compressor 3:1, fast attack, makeup +6
  • Redux Rate 27.7 kHz, Bits 8, Shape soft
  • Auto Filter Low-pass 24, MS2, Res 25%, Freq 5 kHz
You should hear
Loud passages stay clean while each note's tail turns into a fizzing, breathing grain as it decays.
Live edition
Suite

The Emulator II used 8-bit samples with DPCM companding at about 27.7 kHz, and a 4-pole SSM2045 24 dB/oct resonant low-pass (Documented, Wikipedia). Companding means the quantisation noise rises and falls with the signal: loud passages hide it, quiet tails turn into a fizzing, breathing grain. It is the most characterful "old library" sound for string and choir patches. The emulation below is by ear.

  1. Compress hard before Redux (3–4:1, fast attack) so the 8-bit stage sees a hot, even signal: this mimics the compand stage protecting loud passages.
  2. Redux Bits 8, Rate 27.7 kHz. The tail of each note will grain up as it decays: that is the wanted effect.
  3. Auto Filter Low-pass with a 24 dB slope and some resonance for the SSM2045 colour; the MS2 circuit has the softer, rounder peak.
  4. Only the tails should be grainy. If the body of the note sounds crunchy, raise the pre-compression make-up.

Ensoniq EPS/ASR-10: 29.76 kHz, onboard effects and moving loop starts

Instrument: Simpler, Max for Live LFO · Level: intermediate · Genres: boom bap, trip-hop, big beat

Quick start

Load
Simpler, LFO, Redux, Chorus-Ensemble, Hybrid Reverb
Set
  • Simpler Classic, Loop on, Loop 120 ms, Warp off
  • LFO sine 1/2 bar → Simpler Start 10–35%
  • Redux Rate 29.76 kHz, Bits 16
  • Effects Chorus-Ensemble Chorus, Amount 30%; Hybrid Reverb Plates IR, Decay 1.2 s, Dry/Wet 25%
  • Resample the whole result, then chop the print
You should hear
Each note loops a different region of the source: a wet, scanning timbre printed ready to chop.
Live edition
Suite

The ASR-10 sampled at 29.76 or 44.1 kHz in 16 bits and carried its own effects (Documented, Wikipedia); the EPS before it was 13-bit, and the EPS-16 Plus introduced a Transwave loop mode in which the loop start could be modulated (Documented, Wikipedia). A keyboard sampler with effects encouraged printing the effect into the resample, so ASR-style sounds arrive "wet" and are then chopped.

  1. Load a sustained source (organ, choir, string pad) into Simpler Classic, Loop on, a short loop of 80–150 ms.
  2. Max for Live LFO (Suite): map to Simpler's Start, range 10–35%, slow sine or S&H at 1/2. Each note now loops a different region, a timbral scan similar in spirit to Transwave (by ear).
  3. Redux at 29.76 kHz, Bits off (16). Then the effect chain, and resample the whole result: this is the "printed" sample you chop.

Timestretch artefacts: the jungle "metallic" stretch

Instrument: clip warp, Simpler · Level: advanced · Genres: jungle, drum and bass, big beat

Quick start

Load
Simpler
Set
  • Source a sung or spoken phrase recorded at a slow tempo, in a 165 BPM set
  • Warp Beats, Preserve 1/32
  • Transient Loop Mode Back-and-Forth, Envelope 10–30
  • Resample the stretched phrase into Simpler, Warp off
You should hear
A buzzing, stuttered vowel, each grain looping forward and back at a 22 Hz rate tied to the grid.
Live edition
Intro and up

The S1000's timestretch arrived in OS 2.0; its own encyclopedia entry calls it primitive and far from seamless, and notes the sound became popular in its own right; the same page ties the S1000 to UK jungle production (Documented, Wikipedia). Norman Cook time-stretched each vocal line of "Praise You" on the S950 to fit the piano loop (Documented, SOS 2017). Live's warp modes are much cleaner, so to get the era sound you choose deliberately bad settings and resample.

TargetWarp modeSettingResult
Metallic vocal stretchBeatsPreserve 1/32, Transient Loop Back-and-Forth, Envelope 20Buzzing, stuttered vowel
Grainy drone stretchTonesGrain Size 80–120Warbling, choral
Smeared textureTextureGrain Size 40, Fluctuation 25Cloud with flutter
Stretched stab "ring"BeatsPreserve 1/16, Loop ForwardTail replaced by a repeating grain
  1. Place a sung or spoken phrase recorded at a slow tempo into a 165 BPM set. Warp on, Beats mode.
  2. Preserve 1/32, Transient Loop Mode Back-and-Forth, Transient Envelope 10–30. Each grain now loops forward and back to fill time, which buzzes at a rate tied to the grid: at 165 BPM a 1/32 is 45 ms, a 22 Hz buzz.
  3. Resample the stretched phrase. Load the print into Simpler with Warp off, so further pitching is turntable-style.

Two mono halves, processed apart: the riding stereo field

Instrument: Simpler, Auto Pan-Tremolo · Level: advanced · Genres: jungle, drum and bass

Quick start

Load
Audio Effect Rack, Utility, Shifter, Auto Filter, EQ Eight
Set
  • Audio Effect Rack two chains; Utility Channel Mode Left and Right, Mono
  • Shifter Pitch +0.15 st on the left, −0.15 st on the right
  • Auto Filter BP, LFO 2 bars, right chain phase 180°
  • Utility Balance 100L and 100R, pulled back with the Fold macro
  • Low end EQ Eight high pass 150 Hz on both chains, plus an untouched mono chain low pass 150
You should hear
A loop that seems to ride up and spin in the stereo field, while kick and bass stay solid in mono.
Live edition
Standard and up

Rob Playford describes building a break from two mono files adjusted separately, so it seemed to ride up and spin in the stereo field, a trick he had not heard repeated (Documented, SOS 1998). The details of his settings are not given; the Live version below is a technique built from that description, and it works on any sampled loop, not just breaks.

  1. Put the loop on its own track and the Audio Effect Rack above on it. Each chain picks one channel with Utility's Channel Mode and sums it to mono.
  2. Give the halves slightly different pitch (Shifter ±0.1–0.2 st) and opposite-phase slow band-pass LFOs.
  3. Pan them hard and pull back with the Fold macro until it moves without falling apart.
Detuned halves comb-filter when summed to mono. Put an EQ Eight high pass at 150 Hz at the start of both chains and run a third, untouched mono chain below 150 Hz (low pass 150) so kick and bass stay solid on a mono club system.

Chopping melodic samples: one chord per slice, then re-harmonise

Instrument: Simpler (Slice), Sampler · Level: essential · Genres: trip-hop, boom bap, big beat

Quick start

Load
Simpler
Set
  • Simpler Slice, Slice by Manual, a marker on the attack of each chord change
  • Playback Poly, Fade In 1–3 ms, Fade Out 10–30 ms
  • Warp off, so pitch and speed move together
  • Filter high-pass 150–200 Hz to remove the record's bass
  • Detune a slice by 20–40 cents against the rest
You should hear
A new progression from found chords, each re-pitched slice slightly smeared in tempo and timbre.
Live edition
Intro and up

The lo-fi page shows the basic chord-loop chop. The era step beyond it is re-harmonising: slice a phrase into its individual chords and notes, then build a new progression by triggering and transposing slices. Because Simpler with Warp off transposes like a sampler, each re-pitched chord also shifts in tempo and timbre, which is how "found" progressions on these records sound slightly smeared.

  1. Simpler, Slice mode, Slice by Manual. Place markers at each chord change, on the attack, not before it (cutting before an attack leaves the previous chord’s tail in the slice).
  2. Playback Poly so slices can overlap; Fade In 1–3 ms, Fade Out 10–30 ms to stop clicks.
  3. Warp off. Now any slice played on a different key moves pitch and speed together; a slice played 3 semitones down is 19% longer.
  4. Filter high-pass 150–200 Hz to remove the original record's bass, which would fight your new bassline. Replace it with a sine sub (see Sub bass).
Documented: Geoff Barrow describes deliberately layering samples in clashing keys (for example orchestral parts against funk breaks) as a kind of "hip hop tuning" (KEXP, 2019). Detuning a slice by 20–40 cents against the rest is the Live version: Simpler Detune, not a scale fix.

Vocal phrases: pitched-down words and the loop-point vibrato

Instrument: Sampler · Level: intermediate · Genres: big beat, trip-hop

Quick start

Load
Sampler, Echo
Set
  • Sampler Sustain Loop on the steadiest part of the vowel, Snap on, Crossfade 10–25%
  • Loop length 60–90 ms for vibrato-like flutter, 5 ms for a pitched tone
  • Nudge Loop Start and End by single milliseconds while holding a note
  • Pitch play the word 5–7 semitones below root
  • Echo 1/4, Feedback 25%, Reverb 15%
You should hear
A pitched-down word whose sustain wobbles like vibrato rather than clicking or stuttering.
Live edition
Suite

Norman Cook nudged an S950 loop point by tiny amounts to get a vocal loop smooth, so the sustain sounded like vibrato instead of a click (Documented, SOS 2017). A very short sustain loop on a vowel also creates a pitched buzz whose pitch depends on loop length: that is a usable instrument in itself.

Loop lengthBuzzCharacter
5 ms200 HzPitched, synthetic tone
20 ms50 HzGrowly drone under the vowel
60–90 ms11–17 HzFlutter, perceived as vibrato
200+ ms< 5 HzAudible repetition of the syllable
  1. Sampler, Sample tab: Sustain Loop Enabled, loop on the steadiest part of the vowel. Snap on (zero crossings) and Crossfade 10–25%.
  2. Nudge Loop Start and Loop End by single milliseconds while holding a note; listen for the point where the wobble sounds like vibrato rather than a stutter.
  3. For the pitched-down "monster" word, play it 5–7 semitones below root: in Sampler pitch and speed move together, as on the hardware.

Stabs and hits: one record, three layers, a choke group

Instrument: Drum Rack, Simpler · Level: intermediate · Genres: big beat, jungle, trip-hop

Quick start

Load
Drum Rack, Instrument Rack, Simpler
Set
  • Three copies first 30 ms (Attack), the main note (Body), the decay (Tail)
  • Instrument Rack the three nested on one Drum Rack pad, with a Choke group number
  • Attack chain Saturator Analog Clip 4 dB, EQ Eight HP 300 Hz, −4 dB
  • Body chain Simpler Classic, Warp off; Redux 26 kHz, 12 bit
  • Tail chain Hybrid Reverb Plates, 1.8 s, 30%, −8 dB
You should hear
A stab you can re-pitch without smearing its attack, with each new hit choking the previous tail.
Live edition
Intro and up

The big beat page places stabs in a groove; this is how to build them. An era stab is usually three things from the same source record: the attack (first 20–40 ms), the body (a chord or horn note), and the tail (reverb or decay of the recording). Cutting them apart lets you re-pitch the body without smearing the attack, and choke the tail when the next stab arrives, exactly as limited voices did on hardware.

  1. Find a single horn hit, orchestral hit or organ chord on a record. Make three copies in Simpler: first 30 ms (Attack), from 30 ms to the end of the main note (Body), and the decay (Tail).
  2. Nest the three in an Instrument Rack on one Drum Rack pad; give the pad a Choke group number.
  3. Transpose only the Body when playing different pitches. The Attack stays at the original pitch: the ear reads the transient as "the same record".

The "found string": making your own sample that sounds lifted

Instrument: Sampler (Orchestral Strings or any string multisample), Simpler · Level: advanced · Genres: trip-hop, cinematic

Quick start

Load
Sampler, Hybrid Reverb, Glue Compressor, EQ Eight, Vinyl Distortion
Set
  • Perform 4 bars of a two-chord figure, real dynamics, not quantised, slow attack
  • Hybrid Reverb a hall IR at 25–35%
  • Glue Compressor 4:1 slow, then EQ Eight 90 Hz–9 kHz
  • Vinyl Distortion Tracing Drive 30%, Pinch 15%, Crackle low; resample
  • Simpler the print, Classic, Warp off, −1 semitone and a few cents; loop 1 bar
You should hear
A string loop that sounds lifted from a record, slightly off-key and off-tempo against the drums.
Live edition
Suite

The trip-hop genre page builds a string loop from Wavetable and ages it. Go further: perform it as a record would have been played, print it through a chain that imitates the whole path from studio to vinyl to sampler, and only then treat it as a sample. Barrow describes making material that sounded as though it came from full records and then sampling that (Documented, KEXP, 2019); Utley said he began taping everything so it could be sampled later (Documented, SOS 1995).

  1. Perform 4 bars of a two-chord figure on a string multisample with real dynamics (mod wheel or velocity). Do not quantise. Slow attack so the bow is heard.
  2. Add room first (a hall IR in Hybrid Reverb at 25–35%): the found string must contain its own space before it is sampled.
  3. Glue Compressor 4:1 slow, then EQ Eight band-limit to 90 Hz–9 kHz, then Vinyl Distortion. Resample.
  4. Load the print into Simpler Classic, Warp off, and detune it by −1 semitone and a few cents: the off-tempo, off-key relationship to the drums is part of the "found" illusion.
  5. Chop 1 bar of it and loop it; let the arrangement repeat that bar, not your 4-bar performance.

Pressing your own sample: simulated cut, wear and re-sampling

Device: Vinyl Distortion, Redux, Echo, Utility · Level: intermediate · Genres: trip-hop

Quick start

Load
Utility, EQ Eight, Vinyl Distortion, Echo, Simpler
Set
  • Stem your parts bounced together; Utility Mono
  • EQ Eight HP 40, LP 12 kHz, bell −3 dB 3 kHz
  • Vinyl Distortion Tracing drive 30–40%, Pinch 20–30%, Soft, Crackle Density low
  • Echo Wobble 15%, Noise 10%, Feedback 0%, Dry/Wet 15%
  • Resample then slice in Simpler
You should hear
Worn, wobbling slices whose crackle repeats with each slice: the looped dust of the era.
Live edition
Suite

Portishead recorded their own music to vinyl and then manipulated the discs on decks to make samples, distressing records by walking on them (Documented, Wikipedia: Dummy, citing the NYT and NME). In Live, the wear has to be simulated, but the principle carries over: the damage must happen before the chop, so it moves with the sample.

  1. Bounce your own parts together into one mono stem; vinyl lacquers of the period were cut with mono-compatible low end.
  2. Vinyl Distortion: Tracing Model drive 30–40% (the stylus mistracking adds even harmonics), Pinch 20–30%, Soft mode; Crackle Density low.
  3. Echo used mainly for its Wobble and Noise sections: Feedback 0%, Dry/Wet 10–20%, so the short, wobbling copy blurs the pitch slightly like an off-centre pressing.
  4. Resample, then slice. The crackle now lives inside each slice: when you repeat a slice, its crackle repeats too, the tell-tale "looped dust" of the era.

Dust that belongs: matching crackle to the loop length

Device: Simpler, Vinyl Distortion · Level: essential · Genres: trip-hop, boom bap, lo-fi

Quick start

Load
Simpler, EQ Eight, Utility
Set
  • Source one bar of the silent lead-in of a real record
  • Simpler Classic, Loop on, length exactly 1 bar, a click just before beat 1
  • EQ Eight HP 700 Hz, LP 9 kHz
  • Utility Mono, Gain −24 dB, audible only in gaps
You should hear
Crackle that repeats with the loop, audible only in the gaps, so the loop sounds sampled rather than modern.
Live edition
Standard and up

The tape and lo-fi pages cover adding a crackle layer. The era detail is that the crackle in a sampled loop repeats with the loop, so a free-running crackle bed sounds modern while a looped one sounds sampled. Utley's interview mentions the group sampling crackling vinyl as a sound source in its own right (Documented, SOS 1995).

  1. Record (or Re-Pitch-capture) one bar of the silent lead-in of a record: a real surface, not a generator.
  2. Loop it at exactly the music loop's length. Two loudest clicks per bar is plenty; edit the loop start so a click falls just before beat 1.
  3. High-pass at 600–800 Hz so the rumble does not muddy the sub; set the level so it is audible only in gaps (−24 to −30 dB relative to the music).
Do not run Vinyl Distortion's Crackle across the mix bus and call it sampled. Its crackle is random and never repeats, which is exactly what a looped record does not do.

Scratch FX without decks: baby scratch, chirp and the record brake

Instrument: Sampler, Utility · Level: advanced · Genres: trip-hop, big beat, boom bap

Quick start

Load
Instrument Rack, Sampler, Utility
Set
  • Instrument Rack two Samplers on adjacent keys, one forward, one with Reverse on
  • Pitch envelope falling −12 to −24 st over 60–200 ms on each
  • Notes forward/back alternately in 1/16s, Hand Speed macro varied per note
  • Fader Fader macro automated in steps; close it at the start of the back stroke for a chirp
  • Record brake one long forward note, Pitch Env −36 st over 900 ms
You should hear
Baby scratches, chirps and a record brake played from MIDI, without decks.
Live edition
Suite

The boom bap page covers stabs through Beat Repeat and Shifter. A scratch is two movements: the record hand (pitch and direction) and the fader hand (on/off). Build each one separately. Barrow scratched the start of a record on "Wandering Star", inspired by DJ Premier (Documented, KEXP, 2019).

  1. Two Samplers in an Instrument Rack on adjacent keys: one forward, one with Reverse on. Each has a pitch envelope (Pitch/Osc tab or the modulation matrix) falling −12 to −24 st over 60–200 ms.
  2. Write forward/back notes alternately in 1/16s. Short notes are fast hand moves; vary the Hand Speed macro per note with clip automation.
  3. Fader: automate the Fader macro in steps; a chirp is the fader closing at the very start of the back stroke.
  4. Record brake: on the forward chain, a single long note with Pitch Env −36 st over 900 ms and a volume envelope following it down.

Reversed tails: the swell into a stab or a word

Device: Hybrid Reverb, clip Reverse, Simpler · Level: intermediate · Genres: trip-hop, big beat, jungle

Quick start

Load
Hybrid Reverb, Simpler, Redux, EQ Eight
Set
  • Hybrid Reverb Plates IR, Decay 3 s, 100% wet; resample only the return
  • Reverse the clip, trimmed so the loudest moment is the last sample
  • Simpler Classic, Warp off, Transpose −5
  • Redux Rate 22 kHz, Bits 12; EQ Eight HP 250 Hz
  • Timing the swell ends exactly on the dry hit
You should hear
A darker, longer reversed swell that lands on the dry hit and sounds like a sampled effect, not a plug-in.
Live edition
Suite

Print a reverb tail, reverse it, and place it so it ends exactly where the dry sound begins. With a sampler-era twist: pitch the reversed tail with Warp off so it also slows, and crush it, so it sounds like a sampled effect rather than a plug-in.

  1. Send the dry hit to a fully wet Hybrid Reverb; resample only the return.
  2. Reverse the clip, trim so the loudest moment is the last sample. Load into Simpler Classic, Warp off.
  3. Transpose −5 (the swell grows 35% longer and darker). Position the MIDI note so the end of the swell lands on the dry hit: at 90 BPM, a 1-bar swell is 2667 ms.

Pitched tails: octave-down decays and frozen ends

Device: Spectral Time, Simpler, Echo · Level: intermediate · Genres: trip-hop, jungle

Quick start

Load
Simpler, Echo, Spectral Time
Set
  • Simpler a copy of the slice, Start on the last 300 ms, Classic, Warp off, Transpose −12, Loop off
  • Trigger at −12 when the main hit ends
  • Echo Repitch on, 1/4, Feedback 40%, Wobble 20%
  • Spectral Time Freezer on, Retrigger, Fade Out 1.5 s, Dry/Wet 40%
You should hear
A murky octave-down tail that lasts twice as long, optionally frozen under the next section.
Live edition
Suite

Hold the last fraction of a sample and transpose it down: an octave-down tail slows to half speed and drops its aliasing an octave, the classic murky sampler decay. In Live the cleaner alternative for a sustained "end" is Spectral Time's Freezer.

  1. Duplicate the stab or chord slice; on the copy, move Simpler Start to the last 300 ms.
  2. Trigger it at −12 when the main hit ends; it now lasts 600 ms and sits an octave lower.
  3. Echo with Repitch on: automating the delay time during a phrase bends the repeats like a tape varispeed.
  4. Optional: Spectral Time Freezer on the return with Retrigger and a long fade to hold a chord's end under the next section.

Filtered loops: high-passed piano, low-passed verse, the band-passed intro

Device: Auto Filter, EQ Eight · Level: essential · Genres: big beat, trip-hop

Quick start

Load
Simpler, Auto Filter, Utility
Set
  • Simpler 1–2 bar loop, Warp off
  • First Auto Filter Low-pass 24, cut-off on a macro, Res 15%
  • Second Auto Filter High-pass 12, cut-off on a macro
  • States high-pass around 500 Hz, low-pass around 900 Hz, or band-pass 400 Hz–3 kHz
  • Utility Bass Mono below 150 Hz
You should hear
One loop in three filter states that sounds far away without reverb and leaves room for new drums and bass.
Live edition
Intro and up

The simplest arrangement tool of the era: one loop, three filter states. Norman Cook singled out a high-pass filter on the "Praise You" piano as an early discovery he loved (Documented, SOS 2017). Cutting the low end from a loop makes room for the new drums and bass and makes the loop sound "far away" without reverb.

  1. Two Auto Filters in series (one low-pass, one high-pass) rather than one band-pass: you can move each edge independently.
  2. Map both cut-offs to macros; record the macro moves in Session view per section.
  3. Resonance stays low (10–20%) for the "sampled" effect; resonance is the sweep recipe below.

The big beat filter sweep: 8 or 16 bars of resonant build

Device: Auto Filter, LFO · Level: intermediate · Genres: big beat, breaks

Quick start

Load
Auto Filter, LFO, Saturator, Glue Compressor
Set
  • Group everything except the sub, Auto Filter on the group
  • Auto Filter Low-pass 24, DFM circuit, Res 45%, Drive 6 dB
  • Automation cut-off drawn as a curve: slow for 4 bars, fast for the last 2
  • LFO 1/2, ±5–10% on cut-off
  • Glue Compressor 4:1, 3 dB GR; Saturator Analog Clip, Drive 3 dB before it
You should hear
A long resonant sweep up the whole loop that sounds like a hand on a knob, not straight automation.
Live edition
Standard and up

The long resonant sweep up a full loop (drums included) is a big beat staple, by ear. The craft is in the curve: a straight line sounds like automation; an exponential curve with a slow LFO wobble on top sounds like a hand on a knob.

  1. Put everything except the sub on a group, Auto Filter on the group. Sub stays outside or it disappears for 8 bars.
  2. Draw the cut-off automation as a curve (Alt/Option-drag the line in Live 12 to curve it): slow for 4 bars, fast for the last 2.
  3. LFO (Max for Live) at 1/2, ±5–10% on cut-off, for the hand wobble.
At 60% resonance with Drive, a peak crossing a loud kick fundamental can jump 10 dB. Glue Compressor after the filter, and check the peak meter on the group during bar 15.

Sample layering into pads: three sources, one sustained instrument

Instrument: Instrument Rack, Sampler, Simpler · Level: intermediate · Genres: trip-hop, jungle (ambient side), cinematic

Quick start

Load
Instrument Rack, Sampler, Simpler, Redux, EQ Eight
Set
  • Sampler loops each snippet looped, Back-and-Forth where uneven, Crossfade 20–40%
  • Root keys matched by tuning against a Tuner before stacking
  • Detune layers by 5–10 cents in opposite directions
  • Loop lengths no common multiple: 180, 250 and 310 ms
  • EQ keep the pad above 200 Hz
You should hear
Organ, choir and string snippets that breathe together as one sustained, sampled pad.
Live edition
Suite

Many era pads are not synths: they are short sustained moments from records (an organ chord, a choir "ah", a string section's held note) looped and stacked. The jungle "ambient" side and trip-hop's string beds both used this (by ear). Each layer gets its own loop and its own detune so the sum breathes.

  1. Loop each sustained snippet in Sampler (Back-and-Forth where the material is uneven, Crossfade 20–40%).
  2. Root keys must match: set each zone's Root Key by tuning against a reference (Tuner device on the track) before stacking.
  3. Detune layers by 5–10 cents in opposite directions; choose loop lengths with no common multiple (e.g. 180, 250 and 310 ms).
  4. Keep the pad above 200 Hz with EQ; chords low in the stack get muddy fast at 12 bits.

Spring and dub sends tuned for sampled material

Device: Hybrid Reverb (Springs IR), Echo, Roar · Level: intermediate · Genres: trip-hop, dub-influenced big beat

Quick start

Load
EQ Eight, Hybrid Reverb, Roar, Echo
Set
  • Return A pre-EQ EQ Eight HP 350 Hz, LP 4.5 kHz
  • Hybrid Reverb Convolution, Springs IR, Decay 70%, Dry/Wet 100%
  • Roar Single, Dispersion filter, small Drive; then EQ Eight HP 200 Hz, bell −4 dB 2.5 kHz
  • Return B Echo 3/16 L, 1/4 R, Feedback 55%, Wobble 25%, Noise 10%, HP 400 Hz, LP 3 kHz
  • Throws send to 0 dB for one hit on the snare, stab or a word, then back to −inf
You should hear
A short, filtered spring boing and a tape echo that re-excite the snare and words without washing out the loop.
Live edition
Suite

Hybrid Reverb's convolution engine has a Springs IR category (Live 12 manual). A spring's "boing" exaggerates transients, so on a sampled loop it re-excites the crackle and the snare. For a sample send, pre-filter hard and keep the spring short. The dub send recipes in general live on Dub FX and delays; this is the sample-specific version.

  1. Send the snare, the stab and occasional vocal words, not the full loop (the loop already contains its room).
  2. Throws: automate the send to 0 dB for one hit, then back to −inf. A spring throw on the last snare of a phrase is the most era-correct gesture (by ear).

Turntable-speed tricks: hand-slowed records and pitch-fader drift

Device: clip Re-Pitch, warp markers, Simpler · Level: intermediate · Genres: trip-hop, big beat

Quick start

Load
Simpler
Set
  • Warp Re-Pitch, a marker on every beat
  • Markers each beat 5–15% longer than the previous, unevenly
  • Pitch-fader drift clip speed ±1–3% across 8 bars
  • Resample then load into Simpler, Classic, Warp off
You should hear
Pitch that sags and recovers within the phrase, like a record slowed unevenly by hand.
Live edition
Intro and up

Barrow slowed a Johnnie Ray record by hand to make it fit "Biscuit" (Documented, KEXP, 2019). A hand-slowed sample is not a constant speed change: it drags unevenly. In Live, Re-Pitch warp with uneven warp markers reproduces exactly that, because Re-Pitch ties pitch to the local speed between markers.

  1. Warp mode Re-Pitch; add a marker on every beat (select the clip region, then right-click the waveform → Warp from here or add markers manually).
  2. Drag markers so each beat is 5–15% longer than the previous one, unevenly. Pitch now sags and recovers within the phrase.
  3. For pitch-fader drift (a DJ nudging to match tempo), automate the clip's tempo-linked speed by ±1–3% across 8 bars: at ±3% that is about ±0.5 semitone.
  4. Resample before slicing: printed drift sounds performed, live warping sounds edited.

Resampling a whole loop into an instrument

Instrument: Simpler, Sampler, Drum Rack · Level: intermediate · Genres: trip-hop, big beat, jungle

Quick start

Load
Simpler
Set
  • Resample the whole loop for exactly one bar, no master FX
  • Simpler Classic, Warp off, Loop off
  • Fades Fade In 1 ms, Fade Out 5 ms
  • Voices 1 so each note cuts the previous
  • Play +12 for a half-bar chipmunk fill, −12 for a slow-motion outro
You should hear
The whole mixed loop played chromatically, each key a new tempo and key, for fills, breakdowns and key changes.
Live edition
Intro and up

The ultimate sampler-era move: take the entire mixed loop (drums, chords, bass, crackle) and play it chromatically. With Warp off, each key is a new tempo and a new key, which is how loops were "transposed" on the hardware. It turns a one-bar loop into a melodic instrument for fills, breakdowns and key changes. The general resampling routing is on Resampling workflow.

Key vs rootSpeed1 bar at 90 BPM lastsUse
+12×21333 ms (half bar)Chipmunk fill, half-bar stutter
+5×1.3351998 ms (3 beats)Lifts into a chorus
0×12667 msThe loop
−2×0.8912993 msLazy drag, breakdown
−12×0.55333 ms (2 bars)Slow-motion outro
  1. Resample the whole loop for exactly one bar. Drop into Simpler Classic, Warp off, Loop off.
  2. Fade In 1 ms, Fade Out 5 ms. Voices 1 if you want each note to cut the previous (more hardware-like).
  3. Optional: right-click → Simpler → Sampler, then map several root zones (resamples at different tempos) to reduce the "chipmunk" effect on extreme keys.
  4. For a drum-kit version of the same loop: Slice mode → right-click → Slice to Drum Rack (see Sampler, Simpler and Drum Rack).

Sub under the sample: replacing the record's bass

Instrument: Operator, Simpler · Level: essential · Genres: trip-hop, big beat, jungle

Quick start

Load
EQ Eight, Operator, Utility, Tuner
Set
  • Sample track EQ Eight HP 48 dB at 140 Hz
  • Operator sine, Glide 40 ms, Voices 1, on a new MIDI track
  • Sub EQ EQ Eight LP 110 Hz; Utility Mono
  • Tune Tuner on a sustained note of the sample, sub key set to match
  • Notes follow the sample's chord changes on the same slice boundaries
You should hear
A clean, mono sine sub in tune with your track sitting under the filtered sample, with no smeared record bass.
Live edition
Suite

Sampled loops carry bass that is out of tune with your track, out of phase with your kick and smeared by vinyl. Remove it and write a new one. The universal recipe is a clean sine, mono, below the filtered sample.

  1. Tune: find the sample's root with the Tuner device on a sustained note, set the sub's key to match (or transpose the sample).
  2. Follow the sample's chord changes with sub notes on the same slice boundaries.

Processing chain

Order matters: the degradation happens before playback transposition, so artefacts move with the pitch. The filter and saturation come after the sampler, as the hardware's analogue output stage did. Reverb and echo are sends, never baked into the chop unless the effect itself is the found sound (as on an ASR-style print).

Rack

Genre variations

ContextSampler characterMelodic materialTexture and space
Trip-hop (Bristol, 90–96 BPM)S1000-clean or SP-gritty; slow loops pitched downFound strings, noir Rhodes, clashing-key layersPressed/distressed vinyl, spring throws, scratched intros
Big beat (120–135 BPM)S950 grit, resonant S3000 stabs, timestretched vocalsHorn stabs, vocal hooks, high-passed piano loopsLong resonant sweeps, Drum Buss crunch, tape echo throws
Jungle (160–170 BPM)S1000/S1100/S3200; metallic timestretch, split-mono ridesPitched-up stabs, jazz chords, sustained sampled padsReversed tails, octave-down decays, dub echo on vocals
Lo-fi / boom bap crossover (75–95 BPM)SP-1200 per-output voicing, 45→33 captureChopped chord loops, re-harmonised slicesLooped dust, minimal reverb, mono

A short note on sample clearance

This is a factual note, not legal advice. In Grand Upright Music v. Warner Bros. Records (S.D.N.Y., 1991), sampling Gilbert O'Sullivan's "Alone Again (Naturally)" without permission was held to be infringement, after which clearing samples became more expensive and producers used fewer of them or re-recorded the material (Wikipedia). In Bridgeport Music v. Dimension Films (6th Cir., 2005) the court rejected a de minimis defence for copying a short manipulated sample of a sound recording; in 2016 the Ninth Circuit (VMG Salsoul v. Ciccone) declined to follow that reasoning (Wikipedia). Rules differ by country and change over time. Practically, the techniques on this page work just as well on material you record yourself, which is exactly what the found string and pressing your own sample recipes are for.

Common mistakes

Related